Gold's Gym GACR02 manual Assembly, Nylon Locknut yet, Nylon Locknuts yet. Press two 50mm

Page 5

Assembly

Assembly requires two persons. Place all parts of the CORNER BOXING RACK in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires two adjustable wrenches (not included).

M6 Nylon

 

M10 Nylon

M10 Washer

Locknut (25)–6

 

Locknut (23)–17

 

(21)–17

 

 

 

M6 x 30mm Bolt (24)–6

M10 x 35mm Carriage Bolt (22)–4

M10 x 63mm Carriage Bolt (27)–2

 

M10 x 70mm Bolt (18)–5

 

M10 x 65mm Bolt (20)–4

 

 

 

M10 x 95mm Bolt (26)–1

M10 x 15mm Screw (16)–8

 

 

 

1. Press a Large Plastic Cap (15) into the lower

1

 

 

 

 

 

end of the Lower Frame (2). Press a 50mm

 

 

 

 

 

 

 

 

 

 

 

Square Plastic Cap (14) into each Base (5, 6).

 

 

 

 

 

 

Hold the Left and Right Bases (5, 6) against the

 

 

 

 

 

 

Lower Frame (2) as shown. Attach the Bases to

 

 

 

 

2

 

the Lower Frame with an M10 x 70mm Bolt (18)

 

 

 

 

 

and an M10 Nylon Locknut (23). Do not tighten

 

 

 

 

 

 

the Nylon Locknut yet.

 

 

 

 

 

 

See the inset drawing. The CORNER BOXING

 

 

 

 

23

 

14

 

 

 

 

 

RACK is designed to be placed in the corner of

 

5

 

 

 

 

 

 

 

 

a room. If you do not plan to use the CORNER

 

 

 

 

 

18

BOXING RACK in a corner, the Rear Base (19)

 

 

 

 

 

 

should be attached. Position the Rear Base

 

 

 

 

 

 

against the Lower Frame (2) as shown. Attach

 

14

2

 

 

 

the Rear Base to the Lower Frame with the M10

 

 

 

 

5

18

26

 

 

 

x 95mm Bolt (26), an M10 Washer (21), and an

19

15

6

 

 

 

M10 Nylon Locknut (23). Do not tighten the

 

 

 

 

 

 

 

 

 

 

 

Nylon Locknut yet. Next, attach the Rear Base

 

 

 

 

 

 

to the Left and Right Bases (5, 6) with two M10

21

 

18

14

 

 

x 70mm Bolts (18), two M10 Washers (21), and

 

21

 

 

 

 

 

 

two M10 Nylon Locknuts (23). Do not tighten

 

23

 

 

 

14

the Nylon Locknuts yet. Press two 50mm

 

21

6

 

 

 

Square Plastic Caps (14) into the Rear Base.

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

Image 5
Contents Mon.-Fri., 8 a.m.-5 p.m. CST Model No. GACR02Table of Contents Important Precautions Before You Begin Nylon Locknuts yet. Press two 50mm AssemblyNylon Locknut yet Locknuts 23. Do not tighten the Nylon Locknuts yet Nylon Locknuts 23. Do not tighten the Nylon Locknuts yetTighten all of the M10 Nylon Locknuts Used in steps 1, 2, Tighten all eight M10 x 15mm ScrewsPage HOW to Adjust the Corner Boxing Rack How to Use the Corner Boxing RackHOW to USE a Punching BAG Key No. Qty Description Part List-Model No. GACR02Exploded Drawing-Model No. GACR02 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty