Gold's Gym GACR02 manual Nylon Locknuts 23. Do not tighten the Nylon Locknuts yet

Page 6

2. Press a Small Plastic Cap (31) into the Center

2

 

20

 

 

 

Base (7). Attach the Eyebolt (17) to the Center

 

 

 

 

 

 

 

 

 

 

Base with an M10 Nylon Locknut (23) and two

 

 

21

21

5

 

M10 Washers (21) as shown.

 

 

 

 

 

 

 

 

 

Attach the Center Base (7) to the Left and Right

 

 

 

 

 

6

Bases (5, 6) with the four M10 x 65mm Bolts

 

 

 

 

 

 

 

 

 

17

 

(20), four M10 Washers (21), and four M10

 

 

 

 

21

 

 

 

 

21

Nylon Locknuts (23). Do not tighten the Nylon

 

 

 

 

 

 

 

 

 

Locknuts yet.

 

 

 

 

7

20

 

 

 

23

 

 

 

 

 

 

 

 

 

 

31

21

 

 

21

 

 

 

 

 

 

 

 

23

 

 

 

 

 

23

 

 

 

 

 

 

 

 

3. Hold the Left and Right Braces (3, 4) against the

3

 

 

 

 

 

Lower Frame (2) and the Left and Right Bases

 

 

 

 

 

 

 

23

 

 

 

(5, 6). Attach the Braces to the Lower Frame with

 

 

 

 

 

 

 

 

 

 

 

two M10 x 70mm Bolts (18) and two M10 Nylon

 

 

 

 

 

 

Locknuts (23). Do not tighten the Nylon

 

 

 

 

 

 

Locknuts yet.

 

 

 

 

 

 

Tip the Lower Frame (2) and attach the Braces

 

 

3

 

2

 

 

 

 

 

18

(3, 4) to the Bases (5, 6) with the two M10 x

 

 

 

 

 

 

 

 

 

 

 

63mm Carriage Bolts (27) and two M10 Nylon

 

 

 

 

 

 

Locknuts (23).

 

 

23

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

Tighten all of the M10 Nylon Locknuts (23)

 

5

 

 

 

 

used in steps 1, 2, and 3.

 

 

 

 

 

 

 

 

 

 

 

23

 

 

 

27

 

 

 

 

 

 

 

 

27

6

 

 

 

 

 

 

4. See the inset drawing. Press the Large Plastic

4

 

 

 

 

 

Cap (15) into the top of the Upper Frame (1).

 

 

 

 

 

 

 

1

 

 

15

 

 

 

 

 

Hold one of the Large Plates (11) inside of the

 

 

16

 

 

 

Lower Frame (2) as shown. Insert two M10 x

 

 

 

 

21

 

15mm Screws (16) with M10 Washers (21) into

 

 

 

 

 

 

 

21

 

 

1

the right side of the Lower Frame and finger

 

 

 

 

 

 

 

 

16

 

tighten them into the Large Plate. Attach the

 

 

11

 

 

other Large Plate (11) inside of the Lower Frame

 

 

 

 

 

in the same way.

 

 

 

11

 

 

 

 

16

 

Slide the Upper Frame (1) onto the two Large

 

 

 

21

 

 

 

 

 

 

Plates (11). Insert four M10 x 15mm Screws (16)

 

 

21

 

 

 

with M10 Washers (21) into the Upper Frame

 

 

 

 

 

 

 

2

 

16

 

and finger tighten them into the Large Plates.

 

 

 

 

 

 

 

 

 

 

Tighten all eight M10 x 15mm Screws (16).

 

 

 

 

 

 

 

6

 

 

 

 

 

Image 6
Contents Model No. GACR02 Mon.-Fri., 8 a.m.-5 p.m. CSTTable of Contents Important Precautions Before You Begin Assembly Nylon Locknut yetNylon Locknuts yet. Press two 50mm Tighten all of the M10 Nylon Locknuts Used in steps 1, 2, Nylon Locknuts 23. Do not tighten the Nylon Locknuts yetLocknuts 23. Do not tighten the Nylon Locknuts yet Tighten all eight M10 x 15mm ScrewsPage How to Use the Corner Boxing Rack HOW to Adjust the Corner Boxing RackHOW to USE a Punching BAG Part List-Model No. GACR02 Key No. Qty DescriptionExploded Drawing-Model No. GACR02 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT