Gold's Gym GGEL62707.1 manual Wire harnesses do, During this step

Page 6

1.

To make assembly easier, read the information on page 5 before you begin assembling the elliptical exerciser.

Identify the Rear Stabilizer (4). While another person lifts the rear of the Frame (1), attach the Rear Stabilizer to the Frame with two M10 x 75mm Carriage Bolts (34) and two M10 Nylon Locknuts (29).

2.See the inset drawing. Remove the two M10 x 45mm Button Bolts (33) and the packing tubes from the front of the Frame (1). Remove the rubber band from the Lower Wire Harness (87). Discard the rubber band and the packing tubes.

Attach a Wheel (32) to the Front Stabilizer (3) with one of the M10 x 45mm Button Bolts (33) you just removed and an M10 Nylon Locknut (29). Do not overtighten the Nylon Locknut; the Wheel should turn freely.

Attach the other Wheel (32) to the Front Stabilizer (3) in the same way.

3.Slide an M10 Split Washer (94) onto each of the two M10 x 83mm Button Screws (63). Insert the Button Screws into the Front Stabilizer (3). Next, slide the Mast (15) onto the Button Screws and against the Front Stabilizer. Make sure that the Mast is oriented as shown.

While another person holds the Mast (15) and the Front Stabilizer (3) near the Frame (1), connect the Extension Wire Harness (95) to the Lower Wire Harness (87). Insert the connectors on the Wire Harnesses into the Mast.

While the other person lifts the front of the Frame (1), carefully pull the upper end of the Extension Wire Harness (95) to remove any slack. While holding the upper end of the Extension Wire Harness, attach the Mast (15) and the Front Stabilizer (3) to the Frame with the two M10 x 83mm Button Screws (63).

Do not tighten the Button Screws yet.

Make sure that the Wire Harnesses (87, 95) do not get pinched and damaged during this step.

1

 

 

 

 

 

 

29

 

 

 

1

 

 

29

 

 

 

 

4

 

 

 

34

2

Packing

 

 

 

 

 

 

Tube

 

 

 

33

87

 

 

 

 

Packing Tube

1

 

 

 

 

 

 

32

3

 

 

29

 

 

32

 

 

 

33

 

 

3

Pull

 

 

 

 

 

 

 

Make sure that the

 

 

wire harnesses do

 

 

not get pinched

 

 

and damaged

 

 

during this step

 

15

 

 

 

3

95

 

 

63

 

 

 

94

 

 

 

 

87

 

 

 

 

1

6

Image 6
Contents Call TOLL-FREE QUESTIONS?Model No. GGEL62707.1 Serial No Mon.-Fri a.m.-6 p.m. MST Sat a.m.-4 p.m. MSTTable of Contents Important Precautions Before YOU Begin Assembly Wire harnesses do During this stepThis step Wire harnessesHarnesses do not Make surePage Handlebar Leg must be able to pivot freely HOW to USE the Elliptical Exerciser HOW to Adjust the Stride of the ELLIPTI- CAL ExerciserDiagram of the Console Features of the ConsoleHOW to USE the Manual Mode Monitor your progress with the display Turn on the fan if desiredWill automatically turn off Begin pedaling to start the program HOW to USE a Pulse ProgramTurn on the console. See on Select a pulse program Monitor your progress with the display. See onHOW to USE a Preset Program Turn on the console. See on Select a preset programMaintenance and Troubleshooting Battery ReplacementHandgrip Pulse Sensor Troubleshooting Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. GGEL62707.1 Qty DescriptionExploded Drawing A-Model No. GGEL62707.1 R0108A Exploded Drawing B-Model No. GGEL62707.1 R0108A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT