![](/images/new-backgrounds/1134368/13436817x1.webp)
10.Identify the Left Handlebar (9), which is marked with a sticker. Insert the Left Handlebar into one of the Handlebar Legs (79); make sure that the Handlebar
Leg is turned so the hexagonal holes are on the indicated side. Attach the Left Handlebar with two M8 x 45mm Button Bolts (50) and two M8 Nylon Locknuts (46). Make sure that the Nylon Locknuts are inside of the hexagonal holes. Do not tighten the Button Bolts yet.
Assemble the Right Handlebar (not shown) and the other Handlebar Leg (not shown) in the same way.
11.Apply a generous amount of the included grease to the Pivot Axle (81) and to the two M8 Washers (53). Next, insert the Pivot Axle into the Upright (2) and center it.
Reapply grease to both ends of the Pivot Axle.
Slide a Handlebar Spacer (25) onto the short tube on the Left Handlebar (9), and rotate the Handlebar Spacer so the small arrow is pointing toward the floor. Next, slide the Left Handlebar onto the left end of the Pivot Axle (81). Finger tighten an M8 x 25mm Patch Screw (22) with an M8 Washer (53) and a Wave Washer (91) into the end of the Pivot Axle. Then, press the small tabs on a Handlebar Cap (23) into the Handlebar Spacer.
Assemble the Right Handlebar (10) in the same way. Make sure that both Wave Washers (91) are on the Pivot Axle (81), and then tighten both M8 x 25mm Patch Screws (22) at the same time.
12.Apply a small amount of grease to an M10 x 59mm Bolt Set (27) and to the surfaces of the Leg Bushings
(28)in the left Handlebar Leg (79). Attach the left Handlebar Leg to the Left Pedal Arm (14) with the Bolt Set. Do not overtighten the Bolt Set; the left
Handlebar Leg must be able to pivot freely.
Attach the right Handlebar Leg (79) to the Right Pedal Arm (75) in the same way.
See step 3. Tighten the two M10 x 83mm Button Screws (63). See step 4. Tighten the two M8 x 72mm Button Bolts (67). See step 10. Tighten the M8 x 45mm Button Bolts (50) in the Handlebar Legs (79).
10 |
|
|
| |
| 9 |
|
| |
|
| 46 |
| |
| 50 | Hexagonal |
| |
|
| Holes |
| |
| 79 |
|
| |
11 |
|
|
| |
|
| 10 | 23 | |
|
| Tube | 53 | |
9 |
|
| ||
2 | 25 |
| ||
| 22 | |||
|
| |||
|
|
| ||
| Grease |
| 91 | |
|
| Grease | ||
| 25 |
| ||
| Arrow |
| ||
|
|
| ||
Grease | 81 |
|
| |
|
|
| ||
53 | Arrow |
|
| |
|
|
| ||
91 | Tube |
|
| |
22 |
|
|
| |
23 |
|
|
| |
12 |
|
|
| |
|
|
| 79 | |
79 |
|
| ||
| Grease |
| 75 | |
28 | 28 | 27 | ||
| ||||
Grease | 14 |
|
| |
|
|
| ||
| 27 |
|
|
13.Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser.
9