JVC 0403MNMCREJEM Adjusting the Brightness DIMMER - at Power On, When the System is Turned On

Page 13
Basic Operations

Basic Operations

Adjusting the Brightness (DIMMER - at Power On)

You can adjust the brightness of the display.

When the System is Turned On

At power on, each time you press the DIMMER button on the Remote Control, the brightness changes as follows: DIMMER OFF=DIMMER 1=DIMMER 2=(back to the beginning)

DIMMER OFF : Bright

DIMMER 1 : Dark (CD lamp also becomes dark.)

DIMMER 2 : Darker (CD lamp goes out.)

Power Saving Mode (DIMMER - at Power Off)

In power saving mode, you can save the power while the System is turned off (Standby Mode).

Each time you press the DIMMER button on the Remote Control at power off, the display alternates as follows.

DISPLAY ONÔDISPLAY OFF

To enable Power Saving mode, set to “DISPLAY OFF”.

The display completely turns off to save the power.

To restore normal power mode, reset to “DISPLAY ON”. The Clock indicator (Adjusting the Brightness (DIMMER - at Power On)) and the clock appear on the display.

Adjusting the Volume

Turn the VOLUME control on the Unit clockwise to in- crease the volume or turn it counterclockwise to decrease the volume.

Press the VOLUME + button on the Remote Control to in- crease the volume or press the VOLUME _ button on the Remote Control to decrease the volume.

You can adjust the volume level between 0 and 50.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers.

Be sure to turn down the volume before connecting or put- ting on headphones.

When the System is Turned On CAUTION:

•DO NOT turn off the System with the volu- me set to an extremely high level; otherwi- se a sudden blast of sound could damage your hearing, speakers and/or headphones when you turn on the System or start play- ing any source next time.

REMEMBER you cannot adjust the volume level while the System is in standby mode.

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation.

To mute the output, press the FADE MUTING button on the Remote Control. Then, “FADE MUTING” blinks and the output will be faded out and becomes 0.

To release muting, press the FADE MUTING button once again. Then, the output will be faded in to the original level.

•Adjusting the volume causes the muting process (fading out to 0) to release.

•If you use the AHB PRO button or the BASS/TREBLE but- ton during muting, the FADE MUTING button does not

work to release muting. In this case, turn the VOLUME control on the Unit or the VOLUME+/ _ button on the Re- mote Control to newly set the volume.

Reinforcing the Bass Sound (Active Hyper Bass Pro.)

You can reinforce the bass sound to maintain rich, full bass at low volume. (This effect does not apply to the headphones.)

To get the effect, press the AHB PRO button on the Unit or the Remote Control.

“AHB PRO ON” appears and the “BASS” indicator lights up. To cancel the effect, press the AHB PRO button again. “AHB PRO OFF” appears and the “BASS” indicator goes out.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents SP-FSX5 SP-FSX5CA-FSX5FS-X5 Consists of CA-FSX5and SP-FSX5Caution Proper Ventilation Warnings, Cautions and OthersCaution -STANDBY/ON button About the Internal Cooling FanSAFETY INSTRUCTIONS 1 Installation of the System Features2 Power cord IntroductionUsing the Tuner Table of ContentsUsing the CD Player Using External EquipmentsTroubleshooting Table of ContentsCare And Maintenance SpecificationsHow To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied Rear Panel of the Center Unit CA-FSX5Getting Started Connecting the AM MW AntennaRear Panel of the Center Unit CA-FSX5 CAUTIONS Connecting the Speakers SP-FSX5Getting Started Automatic Power On Connecting an External EquipmentCOMPU PLAY On the Remote ControlOn the Remote Control Turning the Power On and OffBasic Operations Turning the System OnWhen the System is Turned On Adjusting the Brightness DIMMER - at Power OnPower Saving Mode DIMMER - at Power Off Adjusting the VolumeTo disable the A.P.off function No signal conditionAuto Power Off A.P.off Tone Control BASS/TREBLETuning In a Station Using the TunerOne Touch Radio 1 Press the FM/AM buttonUsing the Tuner Presetting StationsTo Change the FM Reception Mode Beat Cut AM MW ReceptionUsing the Tuner To show the RDS signals on the displayReceiving FM Stations with RDS To search for a program by PTY codesUsing the Tuner On the Remote ControlAlarm function Using the TunerTo Insert a CD Using the CD PlayerControl Using the CD Player Basics of Using the CD Player - Normal PlayTo Unload a CD To Play a CD2 Press the CD 6button on the Remote Control Using the CD PlayerTo Modify the Program Random PlayCD DOOR LOCK Repeating TracksLocking the CD door Unlocking the CD door2 Press the LINE button on the Remote Control Using External EquipmentsListening to External Equipment Changing the Equipment’s NameUsing External Equipments Adjusting the Input Level3 Press the SET button to finish the adjustment On the Remote ControlSetting the Clock Using the Timers1 Press the CLOCK/TIMER button 2 Press the 3 or 2 button to set the hourUsing the Timers Setting the Daily TimerShowing the Clock DISPLAY Correcting the Clock2 Setting the ON time Example Using the Timers3 Setting the OFF time Example 4 Selecting the music source5 Setting the volume level Turning the Daily Timer On and Off2 Press the CANCEL button 6 Select the FADE functionTimer Priority Setting the SLEEP Timer3 Wait for a few seconds On the Remote ControlSymptom TroubleshootingPossible Cause ActionCleaning the Unit Care And MaintenanceCleaning the Lens Compact DiscsSpecifications 2003 VICTOR COMPANY OF JAPAN, LIMITED 0403MNMCREJEMVICTOR COMPANY OF JAPAN, LIMITED
Top Page Image Contents