JVC LVT1041-002A Tone Control BASS/TREBLE, No signal condition, To disable the A.P.off function

Page 14
Basic Operations

Basic Operations

Tone Control (BASS/TREBLE)

You can control the tone by changing the bass (low frequen- cy) and treble (high frequency).

On the Remote Control

1 Press the BASS/TREBLE button.

Each time you press the button, the Tone Control mode changes as follows.

BASS=TREBLE=Normal display=(back to the beginning)

2 While “BASS” or “TREBLE” appears on the display, press the VOLUME + or - button to adjust the bass or treble level.

You can change the level within the range of -5 to +5. (0: flat)

No signal condition:

Source CD: CD is stopped or no CD is inserted.

When no signal condition continues, “A.P.off 20 sec” (20 seconds left before elapsed time reaches three minutes) ap- pears on the display. The displayed time is counted down and, finally, the System is turned off (Standby mode).

If a CD is played back, the “A.P.off” indicator stops blinking and stays lit again.

If you press a button or turn the VOLUME control, three-minute counting down is reset and counting down newly restarts.

To disable the A.P.off function

When the source is “CD”, press the A.P.off button on the Remote Control until “A.P.off STOP” appears on the dis- play.

Then, the “A.P.off” indicator goes out.

3 Press the BASS/TREBLE button until normal display appears.

Waiting for five seconds will also return the System to the normal display.

Auto Power Off (A.P.off)

You can automatically turn off the System when no signal condition continues for three minutes. This function is ef- fective when the source is set to “CD”, but not to “FM”, “AM” or “ LINE”.

To Enable the A.P.off function (When the source is CD)

1 Press the A.P.off button on the Remote Control until “A.P.off SET” appears on the display.

Then, the “A.P.off” indicator lights up on the display.

Each time you press the button, the display alternates as follows.

A.P.off SET Ô A.P.off STOP

When no signal condition is detected, the “A.P.off” indica- tor will start blinking soon.

Entering the Number with the Remote Control (Numeric Keys)

You will use the Numeric Keys on the Remote Control to enter numbers for presetting stations, recalling the preset stations, selecting track number, or programming the play- ing tracks on a CD.

How to enter the number with the Numeric Keys is ex- plained here.

Examples:

To enter number 5, press 5.

To enter number 10, press 10.

To enter number 15, press +10 then 5.

To enter number 20, press +10 then 10.

To enter number 25, press +10, +10, then 5.

11

Image 14
Contents FS-X5 SP-FSX5CA-FSX5SP-FSX5 Consists of CA-FSX5and SP-FSX5Caution -STANDBY/ON button Warnings, Cautions and OthersCaution Proper Ventilation About the Internal Cooling FanSAFETY INSTRUCTIONS 2 Power cord Features1 Installation of the System IntroductionUsing the CD Player Table of ContentsUsing the Tuner Using External EquipmentsCare And Maintenance Table of ContentsTroubleshooting SpecificationsUsing the Remote Control AccessoriesHow To Put Batteries In the Remote Control Getting StartedUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaUsing the Supplied Wire Antenna Rear Panel of the Center Unit CA-FSX5Rear Panel of the Center Unit CA-FSX5 Connecting the AM MW AntennaGetting Started Getting Started Connecting the Speakers SP-FSX5CAUTIONS COMPU PLAY Connecting an External EquipmentAutomatic Power On On the Remote ControlBasic Operations Turning the Power On and OffOn the Remote Control Turning the System OnPower Saving Mode DIMMER - at Power Off Adjusting the Brightness DIMMER - at Power OnWhen the System is Turned On Adjusting the VolumeAuto Power Off A.P.off No signal conditionTo disable the A.P.off function Tone Control BASS/TREBLEOne Touch Radio Using the TunerTuning In a Station 1 Press the FM/AM buttonTo Change the FM Reception Mode Presetting StationsUsing the Tuner Beat Cut AM MW ReceptionReceiving FM Stations with RDS To show the RDS signals on the displayUsing the Tuner To search for a program by PTY codesOn the Remote Control Using the TunerUsing the Tuner Alarm functionControl Using the CD PlayerTo Insert a CD To Unload a CD Basics of Using the CD Player - Normal PlayUsing the CD Player To Play a CDTo Modify the Program Using the CD Player2 Press the CD 6button on the Remote Control Random PlayLocking the CD door Repeating TracksCD DOOR LOCK Unlocking the CD doorListening to External Equipment Using External Equipments2 Press the LINE button on the Remote Control Changing the Equipment’s Name3 Press the SET button to finish the adjustment Adjusting the Input LevelUsing External Equipments On the Remote Control1 Press the CLOCK/TIMER button Using the TimersSetting the Clock 2 Press the 3 or 2 button to set the hourShowing the Clock DISPLAY Setting the Daily TimerUsing the Timers Correcting the Clock3 Setting the OFF time Example Using the Timers2 Setting the ON time Example 4 Selecting the music source2 Press the CANCEL button Turning the Daily Timer On and Off5 Setting the volume level 6 Select the FADE function3 Wait for a few seconds Setting the SLEEP TimerTimer Priority On the Remote ControlPossible Cause TroubleshootingSymptom ActionCleaning the Lens Care And MaintenanceCleaning the Unit Compact DiscsSpecifications VICTOR COMPANY OF JAPAN, LIMITED 0403MNMCREJEM2003 VICTOR COMPANY OF JAPAN, LIMITED