Kobe Range Hoods IN-027 installation instructions Trouble Shooting, Issue Possible Cause Solution

Page 20

TROUBLE SHOOTING

Issue

Possible Cause

Solution

After Installation,

The power is not on.

Make sure the circuit breaker and the unit’s power is

both motors and

 

ON. Use a voltage meter to check the power supply.

lights are not

The wire connection is not secure.

Check and tighten wire connection.

working.

The control panel and processor board

Check wire continuity from control panel to processor

 

wiring are disconnected.

board.

 

The motor transformer is defective.

Check the power input and power output on the

 

 

motor transformer.

 

 

If it’s needed, replace the motor transformer.

 

 

 

 

The control panel and processor board is

Replace the control panel or processor board.

 

defective.

 

Lights are

The motor(s) is defective.

Replace the motor.

working, but

The capacitor(s) is defective.

Replace capacitor(s).

motor(s) is not.

The control panel or processor board is

Replace the control panel or processing board.

 

defective.

 

The range

The blower system is not secure.

Tighten the turbine impeller/squirrel cage and air

hood is

 

chamber.

vibrating.

The turbine impeller/squirrel cage is

Replace the turbine impeller/squirrel cage.

 

not balanced.

 

 

Hood is not secured in place.

Check the installation of hood, tighten the

 

 

mounting bracket.

The motor is

Halogen Light bulb(s) is defective.

Try placing the trouble light bulb(s) to a working

working, but

 

socket, if the bulb(s) still doesn’t work; replace

the lights are

 

the halogen light bulb(s).

not working.

The light wiring(s) is loose.

Check wire continuity from processor board to

 

 

light transformer to halogen light housing(s).

 

Light transformer is defective.

Check power input and power output on the light

 

 

transformer. If it’s needed, replace the light

 

 

transformer.

 

The control panel or processor board is

Replace the control panel or processing board.

 

defective.

 

 

 

 

The range

The range hood is installed outside of

Adjust the clearance between the range hoods

hood is not

the manufacture recommended

and cook top to 27” to 30”. For Island range

venting out

clearance.

hood, the clearance between the range hoods

correctly.

 

and cook top is 30” to 36”.

 

There is no make-up air inside the

Open the window to enhance the performance

 

house.

of the range hood by creating a sufficient make-

 

 

up air.

 

Obstacle blocking the pipe work.

Remove all obstacles from the duct work.

 

 

 

 

The pipe size is smaller than the

Change the ducting according to the

 

suggested pipe size.

manufacture suggestion.

Cold air is

The pipe connection is not properly

Check the pipe installation.

coming into the

sealed.

 

home.

The damper is not properly installed or

Check the damper installation.

 

is missing from the installation.

 

 

The damper is not installed.

By installing the damper, it will help to eliminate

 

 

air backflow.

18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Kobe Brand Range Hood English Read ALL Instructions Carefully Before Starting ContentsRead and Save These Instructions Important Safety Instructions TOP Grease FirePage Components of Package Range Hood Box Liner Sold SeparatelySafety Warning InstallationCalculation before Installation For Under the CabinetPreparation Before Installation Liner InstallationCustom Hood Preparation Important Peel protective film off the hood, if anyHood Preparation Before Installation Wiring to Power SupplyDuct Work Installation Hood Installation Final AssemblyIndicator Control Operating InstructionsUSE Paper Towel on Stainless Steel MaintenanceTo Clean Aluminum Filter Replacing Light Bulb Specifications IN2730SQBMeasurements & Diagrams Stainless Steel Liner Sold Separately Model No. INL36211A Optional Liner Parts ListModel no IN2730SF Page Circuit Diagram Model NO. IN2730SFTrouble Shooting Issue Possible Cause SolutionDisclaimer Claims will not be Accepted After the Allocated DaysWarranty Warranty CertificateTWO-YEAR Warranty Service Period ConditionsImplied WARRANTIES/STATE LAW ServiceConsequential Damage Record the Following Information for Your Record Product RegistrationRegister Your Product Table DES Matières Lire Attentivement Toutes LES Consignes Avant DE CommencerLire ET Conserver CES Instructions Couper LE Courant Électrique SUR LE Panneau DE Service Consignes DE Sécurité ImportantesPage Contenu DE L’EMBALLAGE Boîte de la hotte de cuisinière Revêtement vendu séparémentConsignes DE Sécurité Hotte Installée Sous UNE Armoire TableauPrise de mesures avant l’installation Préparation de la hotte sur mesure Préparation avant l’installationInstallation du revêtement Installation du système de conduits Branchement à l’alimentation électriqueAssemblage final Préparation de la hotte avant l’installationInstallation de la hotte Mode D’EMPLOI Pour nettoyer les filtres d’aluminium Consigne DE SécuritéEntretien Préventif Remplacement Dune Ampoule Spécifications VitesseMesures ET Schémas Page Liste DES Pièces No DE PièceRevêtement optionnel vendu séparément Schéma DE Câblage Processor BoardProblème Cause probable Solution Avis DE NON-RESPONSABILITÉ Période DE Garantie DE Deux 2 ANS GarantieCertificat DE Garantie Dommages Indirects Garanties Tacites / RéglementationInscrire LES Renseignements Suivants Pour NOS Dossiers Enregistrement DU ProduitEnregistrez votre produit LEA Y Conserve Estas Instrucciones ÍndiceInstrucciones Importantes DE Seguridad Precaución Componentes DEL Paquete Caja de Campana de Extracción Cubierta Vendida por SeparadoCálculo antes de la Instalación InstalaciónPara Instalación Debajo DE UN Gabinete Tabla Instalación de la Cubierta Preparación Antes de la InstalaciónPreparación de la Campana Personalizada Advertencia DE Seguridad Cableado Hacia la Fuente de AlimentaciónInstalación de la Red de Conductos Riesgo DE ELECTROCUCIÓN. Esta Campana DEEnsamblaje Final Preparación de la Campana antes de la InstalaciónInstalación de la Campana Instrucciones DE Operación Control Encendido/ApagadoMantenimiento Para Limpiar el Filtro de AluminioPara Reemplazar el Foco Especificaciones Medidas Y Diagramas Page Cubierta Opcional Listado DE PiezasModelo no IN2730SF Cubierta Opcional Vendida por Separado Diagrama DE Circuito Modelo NO. IN2730SFProblema Posible Causa Solución Cláusula DE Exención No SE Encuentran Cubiertos Bajo Nuestra GarantíaGarantía Certificado DE GarantíaPeriodo DE Servicio DE LA Garantía DE DOS Años CondicionesDaños Emergentes Garantías IMPLÍCITAS/LEY EstatalEscriba LA Siguiente Información Para SUS Archivos Registro DEL Producto¡Registre su Producto VER.090331

IN-027 specifications

The Kobe Range Hoods IN-027 is an exceptional kitchen ventilation solution that stands out for its blend of innovative technology, elegant design, and practical functionality. This range hood is crafted to enhance both the aesthetics and air quality of modern kitchens, making it an ideal choice for home chefs and cooking enthusiasts alike.

One of the standout features of the IN-027 is its powerful yet quiet operation. Equipped with a robust 600 CFM internal blower, this range hood efficiently eliminates smoke, steam, and cooking odors, ensuring a fresh and clean kitchen environment. Thanks to its advanced noise-reduction technology, the IN-027 operates at a whisper-quiet level, allowing you to carry on conversations without distraction even while the hood is in use.

Another defining characteristic of this range hood is its sleek and stylish design. The IN-027 features a commercial-grade stainless steel construction that not only enhances its durability but also adds a touch of elegance to your kitchen. The brushed finish is resistant to fingerprints and smudges, ensuring that it maintains its pristine appearance over time. With dimension options to fit various kitchen layouts, including 30-inch and 36-inch widths, the IN-027 can seamlessly blend into any design aesthetic, whether contemporary or traditional.

The IN-027 is also designed with user convenience in mind. Its intuitive controls allow for easy operation, letting you adjust fan speeds and lighting with minimal effort. The range hood comes with a dishwasher-safe baffle filter that effectively captures grease and contaminants, simplifying maintenance and ensuring long-lasting performance. Moreover, the built-in LED lighting illuminates your cooking area, making it easier to monitor food preparation.

Safety is paramount, and the IN-027 has you covered with its heat-sensitive auto shut-off feature. This smart technology automatically turns off the range hood after a certain period of operation, preventing overheating and potential hazards in the kitchen.

In summary, the Kobe Range Hoods IN-027 is an exemplary choice for anyone seeking an efficient, stylish, and user-friendly kitchen ventilation solution. With its powerful performance, elegant design, and thoughtful features, it not only enhances your cooking experience but also contributes to a healthier indoor environment. Whether you are sautéing, grilling, or baking, the IN-027 ensures that your kitchen remains a pleasant space, free from unwanted odors and smoke.
Top Page Image Contents