Coleman 2000001597 manual Before you begin, To Set Up Tent, Hinged, Rigid Door

Fig. 6

Curved Ridge

Poles with Red

Marking in

center 2 sleeves

Curved End of

Long Leg Pole

Sleeve

with Red

Trim

Ridge Pole with

Red Marking

Button in third hole Fig. 4

WEATHERMASTER® 6 SCREENED TENT

Before you begin

Read all instructions before set up.

•Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines.

•Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.

•Secure with all stakes and guylines provided to prevent property damage or personal injury.

•For best results in windy conditions, position narrow end of tent into the wind.

•Enlist the help of at least one other person to assist you when it is time to assemble the tent.

Pole Descriptions

Description	Qty.	Pole	Pole	Pole
		Dia.	Repair Kit	Replacement Kit
Long Leg Pole, steel
(w/ red marking)	4	19mm	N/A	5010000608
Short Leg Pole, steel	4	19mm	N/A	5010000610
Curved Ridge Pole, steel
(w/ red marking)	2	19mm	N/A	5010000607
Curved Ridge Pole, steel	2	19mm	N/A	5010000609
Awning Pole, black,

MODEL 2000001597

6.Rotate all eight Leg Poles upright and insert

pin on each web loop at the side locations	7A
as shown. (Fig. 7 & 7A)

Pin

Fig. 7

7. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8)

Fig. 8

STITCH LINE

fiberglass, metal tips	1	6.3mm	5010000543	5010000545
Door Pole, long, thin, black,
fiberglass, rubber tips	1	6.3mm	5010000543	5010000545
Vert. Door Pole, short, black,
fiberglass, rubber tips	1	6.3mm	5010000543	5010000545

To Set Up Tent

1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)

Fig. 1

Door

2. Pull four corners of tent taut, then secure by driving stakes through web loops at an angle for better anchoring. (Fig. 2)

Fig. 2

3. Assemble four, steel, shock-corded,

8.To stretch tent to finished size:

•Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.9);

•Pull up on top Leg Pole section until tent is taut;

•Twist the lower Leg Pole clock- wise until the button locks into the center or lowest hole;

•Repeat on remaining Leg Poles.

9.Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 10) NOTE: It may be necessary to remove metal stakes through web straps at side of tent and screen room, pull tent taut, and drive in stakes to secure.

Fig. 9

Upper

Leg Pole

Section

Button

Center Hole

Lower Hole

Lower

Leg Pole

Section

Fig. 10

curved Ridge Poles. Insert Ridge Poles		Fig. 3
	Ridge Pole
(with red marking) into center sleeves	with Red
	Marking
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
		Sleeve
into the other two sleeves on top of tent.		with Red
		Trim

4. Assemble eight, steel, shock-corded, Leg Poles. Push down on steel button on tapered end and insert into end with four holes.

NOTE: Make sure steel button locks

into third hole on pole as shown. (Fig.4) 5. Insert curved end of Leg Poles

(with red marking) into the ends of the Ridge Poles (with red

marking). Insert curved end of remaining short Leg Poles into the ends

of the remaining Ridge Poles. (Fig. 5 & 6)

Fig. 5

Hinged, Rigid Door

1.Assemble Vertical Door Pole (shorter black pole with plastic cap tips); then insert through zippered vertical pole sleeveon hinged side of door. (Fig. 11)

2.Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

3.Assemble Door Pole (longer black pole with plastic cap tips); then insert into zippered pole sleeve at top of door. (Fig. 14)

4.Insert end of Door Pole into top hinge plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

5.Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Fig. 11 Fig. 12 Fig. 13

Vertical Pole

Sleeve

Door Hinge

		Fig. 14	Fig. 15
Top
Door	Pole
Hinge				Fig. 16
	Sleeve

(continued on other side)