Vision Fitness X6000 manual E P 1 Yellow BAG

A s s e m b l y G u i d e

X6000

ELLIPTICAL TRAINER

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.

If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw.

S T E P 1 YELLOW BAG

•Place a piece of packaging under the front of the unit to aid in assembly.

•Secure the front stabilizer to the base

Stabilizer

Guide

Rail

Support

Bracket

S T E P 2

Pedal Arm

Bracket Cover

Pedal Arm

Guide Rail

S T E P 3

Console

S T E P 4 PINK BAG

• Slide the boot onto the console mast.

Rotation

Axle• Unfold the wire harness located in the frame bracket. Wrap the wire tie around

the end of the wire harness. Pull the wire tie and wire harness up through the top of the console mast while simultaneously sliding the mast into the frame bracket.

•Secure the mast to the frame using three lock washers (8x15x2T) and three socket head bolts (M8x60L). Tighten with the 6mm L-Shaped wrench.

• Slide the boot down the console mast and snap it in place on top of the cover.

•Remove the four screws from the back of the console. Plug the wire harness into the back of the console. Connect the heart rate wires from the console mast to the console. Attach the console to the console mast with the four screws.

•Attach the water bottle cage with the screwdriver and the screws located in the console mast.

frame with four bolts (M8x25L) and arc washers (8x17x1.0T). Tighten with the 5mm L-shaped wrench.

S T E P 2 ORANGE BAG S T E P 1

• Connect the guide rail support

bracket to the left and right guide rails

with two washers (8x20x2T) and two

bolts (M8x15L). Tighten with the 5mm

T-handle wrench.

• Slide the bracket ends of the guide

rails over the rear frame tube. Secure

with arc washer (8x17x1.0T), lock

washer (8x15x2T) and bolt (M8x25L)

to the top holes in the guide rails.

Secure with arc washer (10x20x1.5T),

S T E P 4

S T E P

Console

Mast

Boot

S T E P

5

6

GREEN BAG

•Slide a wavy washer (20x29x1.5T) on the lower link arm axle, which is located under the foot plate. Slide the axle through the bracket located o-n top of the pedal arm.

•Secure the link arm to the pedal arm with the pedal support bracket and three bolts (M8x13L). Tighten with the 5mm T-shaped wrench.

•Repeat this step on the left side.

BLACK BAG

lock washer (8x15x2T) and bolt

(M8x75L) to the front holes in the guide

rails. Tighten with the 5mm L-shaped

wrench.

• Slide the rear stabilizers onto each rear	S T E P 6
frame tube axle. Secure with washers
(8x14x1.5T) and bolts (M8x20L).
Tighten with the 5mm T-handle wrench.

S T E P 3 BLUE BAG

• Slide a wavy washer (25x34x2T) onto the right rotation axle. Slide the right pedal arm knuckle onto the right rotation axle. The pedal arm roller wheel should be placed in the groove of the guide rail. Secure in place with a washer (8x38x2T) and bolt (M8x20L). Tighten with a 5mm T-shaped wrench.

•Place the pedal arm bracket cover over the pedal arm knuckle. Secure with a washer (5x10x1T) and bolt (M5x10L). Tighten with the screwdriver.

•Repeat this step on the left side.

S T E P 5

Link Arm

	• On the right side, slide the dual-
	action axle cover onto the console
	mast axle. Slide a wavy washer
	(25x34x2T) onto the axle. Slide the
	right dual-action arm on the axle. Fix
	in place with the washer (8x38x2T)
	and locknut (M8). Cover with the
	included nut cap.
Frame	• Insert the sleeve into the socket joint
Bracket	of the lower link arm. Connect the
	lower link arm to the dual action arm
	with a bolt (M8x30L). Attach the
	washer (8x25x1.5T) and nut (M8) to
	the end of the bolt. Tighten with the
	5mm L-Shaped wrench and 13mm
	wrench.
	• Position the link arm cover over the
	joint of the lower link arm and secure
	the two pieces of the cover together
	with a panhead bolt (M4x15L).
	Connect the cover to each side of the
	lower link arm with a washer
	(5x10x1T) and bolt (M5x12L).
	• Repeat these steps on the left side.

S T E P 7	CONSOLE
	• Please refer to back cover for this step.