ProForm PFTL99600 user manual Follow your progress with the displays

Page 12
Current Segment

The program display will show a simplified profile of the program you have selected. The Time/Segment Time display will show how long the program will last.

3 Press the Start button or the Speed button to start the program.

A moment after the button is pressed, the tread- mill will automatically adjust to the first speed and incline settings for the program. Hold the handrails and begin walking.

Each program is divided into several time seg- ments of different lengths. The Time/Segment Time display shows both the time remaining in the program and the time

remaining in the current

segment. One speed setting and one incline setting are programmed for each segment. The speed setting for the first segment will be shown in the flashing

Current Segment column of the program display. (The incline settings are not shown in the program display.) The speed settings for the next seven segments will be shown in the seven columns to the right.

When only three seconds remain in the first seg- ment of the program, both the Current Segment column and the column to the right will flash, a se- ries of tones will sound, and all speed settings will move one column to the left. The speed setting for the second segment will then be shown in the flashing Current Segment column and the tread- mill will automatically adjust to the speed and in- cline settings for the second segment.

The program will continue in this way until the speed setting for the last segment is shown in the Current Segment column and no time remains in the Time/Segment Time display. The walking belt will then slow to a stop.

Note: Each time a segment ends and the speed settings move one column to the left, if all of the indicators in the Current Segment column are lit, the speed settings will move downward so that only

the highest indicators in the columns will appear in the program display. When the speed settings move to the left again and not all of the indicators in the Current Segment column are lit, the speed settings will move back up.

If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed or Incline buttons on the console. Every few times one of the Speed buttons is pressed, an additional indicator will light or darken in the Current Segment column. If any of the columns to the right of the Current Segment column have the same number of lit indicators as the Current Segment column, an additional indicator may light or darken in those columns as well. Note: If you manually adjust the speed setting so that all of the indicators in the Current Segment column are lit, the speed settings in the program display will not move downward as described above. When the current segment of the program ends, the treadmill will automati- cally adjust to the speed and incline settings for the next segment.

To stop the program temporarily, press the Stop button. The Time/Segment Time display will begin to flash. To restart the program, press the Start but- ton or the Speed button. To end the program, press the Stop button, remove the key, and then reinsert the key.

4 Follow your progress with the displays.

Refer to step 5 on page 10.

5 Measure your heart rate, if desired.

See step 6 on page 11.

6 When the program is completed, remove the key from the console.

When the program has ended, make sure that the incline of the treadmill is at the lowest set- ting. Next, remove the key from the console and put it in a safe place.Note: If the displays and various indicators on the console remain lit after the key is removed, the console is in the “demo” mode. Refer to page 18 and turn off the demo mode.

When you are finished using the treadmill, move the on/off switch near the power cord to the off position and unplug the power cord.

12

Image 12
Contents QUESTIONS? Model No. PFTL99600 Serial NoCustomer HOT Line Table of Contents Important Precautions Page Before YOU Begin Left Side Right SideAssembly Driver and rubber malletPage Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeWhen you are finished, remove the key HOW to USE Personal Trainer ProgramsCalories/Fat Calories Measure your heart rate, if desiredFollow your progress with the displays HOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Audio Adapter CableInsert the key into the console PressVCR. the Play button on your CD player orWhenkey. the program is completed, remove HOW to USE Programs Directly from OUR Internet Site When the program has ended, remove the keyFollow the on-line instructions to start the program Information MODE/DEMO Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETROUBLE-SHOOTING Problem The power turns off during useTop Problem The thumb pulse sensor does not function properly Problem The walking belt slows when walked onConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR0202A Key Qty DescriptionExploded DRAWING-Model No. PFTL99600Exploded DRAWING-Model Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT