ProForm PFTL99507.1 user manual Bolts and then tighten them, Be careful not to pinch the wires

Page 9

7.Have a second person hold the Bridge (95) near the Right Upright (78). Remove the wire tie from the Upright Wire (38).

Connect the Upright Wire (38) to the Bridge Wire (52). See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

8.Insert the indicated connectors into the Right Upright (78).

Next, insert the fronts of the brackets on the Bridge (95) into the Uprights (74, 78), and then fully insert the brackets. Make sure that the plas- tic edges of the Bridge are inside the Uprights.

Attach the Bridge (95) with six 1/4" x 1/2" Bolts

(7) and six 1/4" Star Washers (10); start all six

Bolts and then tighten them.

See steps 4 and 6. Tighten the four 3/8" x 4 1/2" Bolts (6).

9.With the help of a second person, hold the con- sole assembly near the Bridge (95). Connect the Bridge Wire (52) to the console wire. See the inset drawing in step 7. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

Connect the Console Ground Wire (101) to the console assembly ground wire. Insert the wires into the console assembly.

Attach the console assembly with three 3/8" x

1 1/4" Bolts (5) and three 3/8" Star Washers (9).

Be careful not to pinch the wires.

7

95

52

38

78

Wire Tie

 

52

 

38

8

 

 

95

 

Connectors

10

7

Front

7

 

 

Edge

 

7

74

10

 

 

7

 

78

9

 

Console

 

Assembly

 

Console

Wires 52

101

95

9

5

9

Image 9
Contents Please do not Contact QUESTIONS?Call TOLL-FREE On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged Not fully tighten the Bolts yet Careful not to pinch the Upright WireNot fully fold the Frame yet Tighten the Nut the Wheel must turn freelyBolts and then tighten them Be careful not to pinch the wiresPage Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired Follow your progress with the displayStand on Foot rails Avoid moving Your handsSelect a personal trainer workout HOW to USE a Personal Trainer WorkoutPress the Start button to start the workout Follow your progress with the display. See onSelect the iFIT Competition Training Center HOW to USE the Ifit Competition Training CenterSelect the settings mode HOW to USE the Settings ModeMeasure your heart rate if desired. See on Enter user informationInformation Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description R1207AQty Exploded Drawing A-Model No. PFTL99507.1 R1207A Exploded Drawing B-Model No. PFTL99507.1 R1207A Exploded Drawing C-Model No. PFTL99507.1 Exploded Drawing D-Model No. PFTL99507.1 R1207A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT