ProForm PFTL49906.0 user manual Troubleshooting, Problem The power turns off during use, Top

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two Foot Rail Screws

(26)and the two 3/4” Screws (3) and carefully remove the Hood (56).

a

3

 

26

 

56

26

Locate the Reed Switch (59) and the Magnet (63) on the left side of the Pulley (84). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8". If necessary, loosen the Screw (22), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

1/8"

84

22

 

59

63

Top

 

View

 

19

Image 19
Contents Model No. PFTL49906.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Back Right Side Before YOU BeginAssembly Not tighten the Upright Bolts yet Washers 6 do not tighten the Upright Bolts YetNut yet Outer side of the Frame Spacer facingA Nut 12 firmly tighten the two Nuts Used in steps 5 Upright Wire Side View View from Above Front ViewCareful not to overtighten the Screws Screws 83. Be careful not to overtightenHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power HOW to USE the Manual Mode Measure your heart rate if desired HOW to USE a Preset Program HOW to USE the Stereo Sound System When the program ends, remove the key from ConsoleInformation Mode HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description Part LIST-Model No. PFTL49906.0Model Exploded Drawing B-Model No. PFTL49906.0 R1106A Exploded Drawing C-Model No. PFTL49906.0 R1106A Exploded Drawing D-Model No. PFTL49906.0 R1106A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT