ProForm PFTL49507.0 user manual Troubleshooting, Problem The power turns off during use

Page 21

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If you need further assistance, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 11. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes, and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The display of the console does not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

11

POWER CORD. With the help of a second person,

 

 

 

carefully tip the Uprights (70, 76) down as shown.

 

 

Remove the three Screws (11) and two 3/4" Screws

 

70

(23). Note: A Phillips screwdriver with a shaft at least 5

 

 

in. (13 cm) long is required.

 

23

 

 

23

 

76

 

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents QUESTIONS? Model No. PFTL49507.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedUpright Bolts yet Do not tighten the Upright Bolts yet See steps 2 and 4. Fully tighten the two Endcap ScrewsTighten the Bolts yet Connectors are not Connected Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired Calories/DistanceOn the foot rails Avoid movingSelect one of the personal trainer quick programs HOW to USE a Personal Trainer Quick ProgramHOW to Create Your OWN Quick Program Follow your progress with the matrix and the displaysSelect a custom quick program Select a custom quick programs HOW to USE Your OWN Quick ProgramInformation Mode HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onPage Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description R0607AKey No. Qty Description Exploded Drawing A-Model No. PFTL49507.0 R0607A Exploded Drawing B-Model No. PFTL49507.0 R0607A Exploded Drawing C-Model No. PFTL49507.0 R0607A Exploded Drawing D-Model No. PFTL49507.0 R0607A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents