3. Insert the upper end of a Handrail (85) into the right | 3 |
| |
Upright (82) as shown. Note: It will be necessary to |
| ||
|
| ||
pivot the Handrail to the side and back repeatedly |
|
| |
(see arrow A) while pushing on the Handrail (see |
|
| |
arrow B) to insert it fully into the Upright. Next, pivot |
| B | |
the lower end of the Handrail down, push it toward the |
| ||
|
| ||
right Upright, and then align it with the indicated hole. | 82 | 85 | |
Insert the other Handrail (85) into the left Upright (82) as |
| 82 | |
|
| ||
described above. |
|
| |
| 85 |
| |
|
| A | |
|
| Hole | |
4. With the help of a second person, carefully tip the | 4 | 97 | |
Uprights (82) down as shown. Make sure that the | |||
| |||
Extension Legs (103) remain in the Uprights. |
|
|
Tighten a Handrail Bolt (78) with a Handrail Washer (36) |
|
| 82 | |
into each Extension Leg (103) and Handrail (85). Note: If |
|
| 116 | |
it is difficult to thread the Handrail Bolts into the Hand- |
|
| ||
|
| 101 | ||
rails, pull one of the Handrails to the side and thread a |
|
| ||
Handrail Bolt into the bottom of the Handrail. Notice the |
|
| 103 | |
angle of the Bolt. When attaching the Handrails to the |
|
| 78 | |
Extension Legs, insert the Bolts and Washers at the ob- |
|
| ||
82 |
| 97 | ||
served angle. It should be close to the same angle as | 116 | |||
85 |
| |||
the Handrails (see the inset drawing). | 101 |
| ||
| 103 |
|
| |
Note: Refer to figure 4b. If it is difficult to align the hole in |
| 36 | 85 | |
a Handrail (85) with the hole in an Extension Leg (103), |
| 78 | ||
| 36 78 | |||
it may be necessary to move the Handrail up or down or |
| 97 |
| |
have a second person stand on the treadmill and lift the |
|
|
| |
Handrail. | 4b |
|
| |
|
|
|
Next, attach each Extension Leg (103) with two Screws (101) and a Base Pad (116) as shown in drawing 4. Make sure that the Extension Legs are fully inserted into the Uprights (82). It may be necessary to push down on the Uprights as you tighten the Screws.
With the help of a second person, carefully tip the
Uprights (82) back to the upright position.
Note: One replacement Base Pad (116) and Spacer (not |
|
| |
shown) are included. If a Base Pad becomes worn and |
|
| |
needs to be replaced, use the replacement Base Pad. If |
| 85 | |
a Thick Base Pad (97) needs to be replaced, use the re- | 103 | ||
| |||
placement Base Pad with the Spacer. |
|
|
5.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet |
|
from damage, place a mat under the treadmill. | 7 |