ProForm PFTL721040 user manual

Page 7

2.With the help of a second person, carefully tip the Uprights (97) down as shown. (Note: It may be helpful to place one foot on one of the Extension Legs [92] as you tip the Uprights.) Make sure that the Extension Legs remain in the Uprights.

Attach the Extension Legs (92) with four 1” Tek Screws (80) and two Base Pads (99) as shown. Tighten the Tek

Screws without the Base Pads first. Note: The indi- cated center holes are not used.

Attach the other two Base Pads (99) to the base of the Uprights (97) in the locations shown with two 1” Tek Screws (80).

With the help of a second person, raise the Uprights (97) to the vertical position.

3.Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two col- lars, place one on each side of the spring.) Insert the pin into the Latch Housing (82), and tighten the knob back onto the pin.

4.See drawing 4c. With the help of a second person, hold the Console Base (101) near the Uprights (97). Look under the Console Base and locate the wires on the sides of the Console Base. Make sure that the wires are not routed through the openings for the Trays (109,

111). Drawing 4a shows the correct route for the wires; drawing 4b shows an incorrect route.

See drawing 4c. Locate the Wire Harness (74) and the pulse wire in the Uprights (97). Cut the plastic ties secur- ing the Wire Harness and the pulse wire.

Connect the Wire Harness (74) and the pulse wire to the connectors on the sides of the Console Base (101).

Make sure to connect the connectors properly (see the inset drawings). The connectors should slide to- gether easily and snap into place. If the connectors do not slide together easily and snap into place, turn a con- nector and try again to insert it. IF THE CONNECTORS

ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the excess Wire Harness and pulse wire up into the Console Base.

2

 

 

99

 

 

 

 

 

 

80

 

99

 

99

 

 

 

 

 

 

80

 

80

 

 

 

Not

 

 

 

Used

80

 

 

97

 

 

99

92

 

 

 

 

97

 

80

 

Not

92

 

 

Used

 

 

 

 

 

3

 

 

 

 

82

 

 

Knob

 

 

 

 

Collar

 

 

 

Pin

 

 

 

Spring

 

4a

 

4b

 

 

Correct

Incorrect

 

4c

 

 

 

 

111

109

 

 

 

 

 

101

 

 

74

 

 

 

97

97

 

 

Pulse

74

Wire

 

7

Image 7
Contents Model No. PFTL721040 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyPage 107 HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredWhenkey. you are finished exercising, remove Select one of the preset programs HOW to USE a Preset ProgramSelect a pulse program HOW to USE a Pulse ProgramEnter your age Enter a maximum speed settingSelect one of the custom programs HOW to Create Custom ProgramsHOW to USE a Custom Program HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoHOW to Connect Your VCR Measure your heart rate if desired Follow the on-line instructions to start Program Directly from OUR WEB SiteReturn to the treadmill and stand on the foot Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R1104AQty Exploded DRAWING-Model No Exploded Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT