ProForm PFTL69712 user manual Assembly, Right Left

Page 6

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own 7/16” and 9/16” wrenches , rubber mallet , wire cutters ,

and Phillips screwdriver.

Use the part chart attached in the center of this manual to identify small parts used in assembly. Each bag of hardware is labeled with the corresponding assembly step.

1.With the help of another person, carefully tip the treadmill onto its left side. Have the other person continue to hold the treadmill during steps 1 through 4. Note: Only half of the hardware in the bags for steps 1 to 3 will be used. The remaining hardware will be used at the end of step 4.

Identify the Right Upright (58), which contains the Wire Harness (55). Insert the round tube on the Right Upright into the Base (117) as shown. If necessary, apply grease to the round tube and use a rubber mallet. Hold a Star Washer (113) between the indicated tab and the Base, and Finger tighten an Upright Bolt (66) through the tab into the Base.

Make sure that the two indicated Walking Platform Screws (114) in the Walking Platform (100) are tight.

1

66

55

 

 

 

Tab 113

117

58

100

114

2.Attach a Base Leg (78) to the Base (117) with two Base Leg Bolts (77) and two Base Leg Nuts (70). Make sure that the Base Pad (75) is in the position shown. (Note:

The Base Leg Nuts fit into square holes in the Base. If necessary, push or pull on the Right Upright [58] to align the holes.) Do not fully tighten the Base Leg Bolts yet.

3.See the inset drawing. Identify the right Front Wheel (62) by observing the direction that the Wheel Bracket (64) slants.

Locate four 3/4” Screws (12) in hardware bag number 4. Attach the Wheel Bracket (64) on the right Front Wheel (62) to the Base (117) with the four Screws.

Attach a Thin Base Pad (103) and a Thick Base Pad (75) to the Base (117) with two 3/4” Screws (12) as shown.

2

58

 

77

66

 

75

 

78

 

77

 

70

 

117

3

62

 

 

117

 

 

 

103

 

 

 

64

 

 

 

12

62

Right

Left

12

 

 

 

75

 

 

 

 

64

 

 

6

Image 6
Contents QUESTIONS? Model No. PFTL69712 Serial NoCustomer HOT Line Table of Contents Important Precautions Page Before YOU Begin Left SideRight Side Assembly Right Left124 Side View Page Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeDistance/Laps Measure your heart rate if desiredOn the foot rails and place your HOW to USE Personal Trainer Programs Select one of the personal trainer programsFollow your progress with the displays When the program is completed, remove Key from the consoleHOW to USE Heart Rate Programs Put on the chest pulse sensorEnter your age HOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerInsert the key into the console HOW to Connect Your VCRAudio Adapter Cable PressVCR. the Play button on your CD player orWhenkey. the program is completed, remove HOW to USE Programs Directly from OUR WEB Site Follow the on-line instructions to start ProgramReturn to the treadmill and stand on the foot Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useTop Problem The walking belt slows when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyPage Part LIST-Model No. PFTL69712 Key Qty DescriptionExploded Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT