ProForm 831.24723.2 user manual

Page 8

5.With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (48) so the treadmill is more stable; do not fully fold the Frame yet.

Remove and discard the two indicated bolts (A) and the shipping bracket (B).

Attach a Base Pad (81) to the Base (85) in the location shown with a Base Pad Spacer (104) and an M4 x 25mm Screw (2). Then, attach an- other Base Pad (81) with only a Screw (2).

Remove the M10 Nut (33), the M10 x 50mm Bolt (27), and the shipping bracket (C) from the Base (85). Attach a Wheel (86) with the Bolt and the Nut that you just removed. Do not over- tighten the Nut; the Wheel must turn freely. Discard the shipping bracket.

6.With the help of a second person, hold a Bolt Spacer (79) inside the lower end of the Left Upright (73). Insert a M10 x 96mm Bolt (5) with a M10 Star Washer (8) into the Left Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (79), Bolt (5), and Star Washer (8).

Orient the Left Upright (73) and the Left Upright Spacer (83) as shown. Hold the Left Upright Spacer and the Left Upright against the Base (85). Finger tighten the M10 x 96mm Bolts (5); do not fully tighten the Bolts yet.

Press a Base Endcap (82) into the Base (85).

With the help of a second person, tip the tread- mill so that the Base (85) is flat on the floor.

7.Set the Console (87) face down on a soft sur- face to avoid scratching the Console. Identify the Right Handrail (90), which has a large hole in the location shown. Hold the Right Handrail near the Console. Attach the console ground wire to the Right Handrail with an 1/2" Screw (3).

Next, insert the console wire into the large hole in the Right Handrail (90) and out of the top as shown. Attach the Right Handrail with three M4 x 19mm Screws (1). Make sure that no wires are pinched. Start all three Screws before tightening any of them; do not overtighten the Screws.

Attach the Left Handrail (not shown) to the Console (87) in the same way. Note: There are

no wires on the left side of the Console.

5

 

 

 

 

 

B

 

A

 

 

 

 

 

 

85

81

 

 

48

 

 

 

2

 

 

27

 

 

 

 

 

104

 

 

 

 

86

 

 

2

81

 

 

 

C

 

 

 

33

6

 

 

 

5

 

 

73

8

 

 

 

 

 

83

 

79

 

 

 

79

 

 

 

82

85

 

 

7

 

 

 

 

 

Console

90

1

Wire

Large Hole

Console

1

 

Ground Wire

 

 

22

87

 

8

Image 8
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Page Before YOU Begin Do not fully fold the Frame yet AssemblyMake sure that the power cord is unplugged Fully tighten the Bolts yet Careful not to pinch the Upright WireStep with a second Bolt Spacer 79, Bolt Star Washer Page Page Knob PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Lower right dis- play-The lower rightUpper dis- play-The upper display can show Select length of workout if desired HOW to USE a Preset WorkoutSelect a preset workout. To select a preset work Information Mode HOW to USE the Crosswalk ArmsHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR0607A Key No. Qty DescriptionIf a part is missing, call Exploded Drawing A-Model No Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No DAY Full Warranty Get it fixed, at your home or ours