ProForm 831.293032 Troubleshooting, Problem The power does not turn on, Solution, Power Cord

Page 13

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at

1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call our toll-free HELPLINE.

PROBLEM: The displays of the console do not function properly

SOLUTION:

a. Remove the key from the console and

UNPLUG THE

 

POWER CORD.

Remove the two 3/4” Screws (2)

 

from the hood, and carefully pivot the Hood (1) off.

a

2

1

Locate the Reed Switch (10) and the Magnet (18) on

the left side of the Pulley (17). Turn the Pulley until the

Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed

Switch is about 1/8”. If necessary, loosen the Screw

(56)and move the Reed Switch slightly. Retighten the Screw. Re-attach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8”

17

10

 

56

18

Top

 

View

 

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Serial Number Decal Model No Serial NoSears, Roebuck and Co Hoffman Estates, IL Important Precautions Table of ContentsUse Never leave the treadmill unattended while itMove the Treadmill on Never insert any object into any openingBefore YOU Begin Using the treadmillRight Side BackRubber mallet Wire cutters AssemblyEnsion Leg 63 in the same way Extension Leg 63 as you tip the UprightsHandrail Cap with Insert the bracket on the Right Handrail 72 into the topUsed in assembly step Connector on the back of the ConsoleTor does not Side of the Right HandrailPerformant Lube HOW to Plug in the Power CordThis product must be grounded.If it should malfunc Grounded Outlet BoxTo reduce the possibility of electric shock Console DiagramWater bottle in the water bottle holder STEP-BY-STEP Console OperationFollow your progress with the three displays Time/Distance Change the incline of the treadmill as desiredFat Calories/Calories Speed display -ThisHOW to Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Lower the Treadmill for USE Problem The power does not turn on TroubleshootingProblem The power turns off during use SolutionCome damaged. Remove the key Problem The walking belt slows when walked onBelt has shifted to the left Walking belt has shifted to the rightExercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyFull 90 DAY Warranty Part Identification Chart Key Qty Description Incline Motor White Wire, 2F Incline BracketMagnet Lock PinR1102A 831.293032
Top Page Image Contents