ProForm 831.293032 Connector on the back of the Console, Tor does not, Side of the Right Handrail

Page 7

6.Place the Console Base (47) on the Right Handrail (72) and the Left Handrail (not shown). Attach the Console Base with four 3/4” Screws (2) (only two Screws are shown). Do not overtighten the Screws.

Insert the Wire Harness (42) through the two indicated

plastic ties on the Console Base (47). Next,

touch the

Right Handrail (72) to discharge any static.

Plug the

widest connector on the Wire Harness into the widest

 

connector on the back of the Console (43).

If the connec-

tor does not

fit easily ,rotate it and then connect it.

 

Plug the other connector on the Wire Harness into the other connector on the Console.

7. Insert the excess Wire Harness (42) into the large hole in

the side of the Right Handrail (72).

Securely tighten the

plastic ties on the bottom of the Console Base (47) to

prevent the Wire Harness from slipping.

Then, cut off

the ends of the plastic ties.

 

Route the Wire Harness (42) through the indicated open- ing in the C onsole Base (47). Attach the Wire Cover to the Console Base (47) with a 1/2” Silver Screw (48).

Tighten two 3/4” Screws (2) into the Console Base (47).

8.Attach a Wheel (66) to the inner side of each Extension Leg (63) with a Wheel Bolt (64) and a Wheel Nut (13) as

shown. Do not overtighten the Bolt.

The Wheel should

be able to spin freely.

 

Lift the treadmill frame (see HOW TO FOLD THE TREADMILL FOR STORAGE on page 11), but do not

latch it. Make sure that the frame is centered between

6

47

 

42

 

Ties

2

43

 

 

72

7

 

 

 

Ties

42

Opening

47

 

 

 

 

 

 

 

44

72

 

 

 

 

 

48

2

 

 

 

8

 

 

 

the Handrails (not shown).

Firmly tighten the bolts

used in assembly step 4.

Then, lower the frame to the

floor.

 

13

63

64

66

9. Make sure that all parts are properly tightened before you use the treadmill.Note: Extra hardware may

be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the walking belt (see page 14). To protect the floor or carpet, place a mat under the treadmill.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Serial Number Decal Model No Serial NoSears, Roebuck and Co Hoffman Estates, IL Important Precautions Table of ContentsNever insert any object into any opening Never leave the treadmill unattended while itUse Move the Treadmill onBack Using the treadmillBefore YOU Begin Right SideExtension Leg 63 as you tip the Uprights AssemblyRubber mallet Wire cutters Ension Leg 63 in the same wayHandrail Cap with Insert the bracket on the Right Handrail 72 into the topSide of the Right Handrail Connector on the back of the ConsoleUsed in assembly step Tor does notGrounded Outlet Box HOW to Plug in the Power CordPerformant Lube This product must be grounded.If it should malfuncSTEP-BY-STEP Console Operation Console DiagramTo reduce the possibility of electric shock Water bottle in the water bottle holderSpeed display -This Change the incline of the treadmill as desiredFollow your progress with the three displays Time/Distance Fat Calories/CaloriesHOW to Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Lower the Treadmill for USE Solution TroubleshootingProblem The power does not turn on Problem The power turns off during useWalking belt has shifted to the right Problem The walking belt slows when walked onCome damaged. Remove the key Belt has shifted to the leftExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesFull 90 DAY Warranty Part Identification Chart Lock Pin Incline Motor White Wire, 2F Incline BracketKey Qty Description MagnetR1102A 831.293032
Top Page Image Contents