ProForm 831.297690 user manual Assembly, Do not Cut

Page 5

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own phillips screwdriver , adjustable wrench and scissors .

1.With the help of a second person, carefully lay the treadmill on its right side.

Insert an Extension Leg (103) into the base of the left Upright (82) as shown. Make sure that the Extension Leg is turned so the Warning Decal (20) is on the side shown. Tighten two of the four Short Screws (101) into the left Upright and the Extension Leg. Attach the other Extension Leg in the same way.

With the help of a second person, carefully raise the treadmill to the vertical position so that both Extension Legs (103) are resting flat on the floor.

2.Refer to HOW TO LOWER THE TREADMILL FOR USE on page 11. Follow the instructions in step 2 to lower the treadmill.

Without removing the tape from the Latch (77), attach the Latch to the left Upright (82) with two 3/4Ó Screws (81). Make sure that the Screws are tight, but do not overtighten them; if the Screws are overtightened, the Latch will not slide smoothly. After the Latch is attached, remove any visible tape.

Note: The inset drawing shows how the parts of the Latch (77) fit together.

3.Cut the plastic tie off the bracket on the base of each Upright (82). Next, cut the plastic tie off the Left Handrail (74). Position the Left Handrail on the left Upright (82). The bracket on the base of the left Upright should be in- side of the lower end of the Left Handrail, as shown in inset drawing C.

Refer to inset drawing A. While a second person holds the Right Handrail (85) and the Console (not shown) near the right Upright (82), cut the indicated plastic ties off the Right Handrail. Do not cut the other plastic tie in the Right Handrail. Next, cut the plastic tie off the Upright Wire Harness (34) in the right Upright (82). Do not drop the Upright Wire Harness into the right Upright.

Refer to inset drawing B. Connect the Console Wire Harness (48) to the Upright Wire Harness (34). The latch on the Console Wire Harness should snap onto the Upright Wire Harness. If the Wire Harnesses do not fit together easily, turn them; do not force the Wire Harnesses together.

1

 

 

 

 

82

 

 

101

 

 

 

103

 

 

 

 

20

 

 

2

 

 

 

82

 

 

 

77

Spacer

 

 

81

 

 

 

 

 

 

Springs

 

 

 

77

 

Bracket

 

3

Do not

A

48

 

 

85

 

cut

 

 

74

 

Plastic

 

 

Ties

 

Plastic Tie

 

82

34

 

 

B

 

 

 

48

 

 

 

34

 

 

Plastic

C

 

82

Tie

74

 

 

 

 

 

Bracket

5

Image 5
Contents SEARS, Roebuck and CO., Hoffman ESTATES, IL Model No Serial NoImportant Precautions Table of ContentsPage Left Side Right Side Before YOU BeginDo not Cut AssemblyTie Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord On the face of the console, remove it Key Console DiagramSTEP-BY-STEP Console Operation Insert the key fully into the consoleCALS/FAT Cals DISTANCE/LAPSInformation Mode When you are finished, remove the keyHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USESymptom the Power does not Turn on TROUBLE-SHOOTINGSymptom the Power Turns OFF During USE TopProblem The walking belt slips when walked on Problem The walking belt slows when walked onProblem The walking belt is off-center when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Key No. Qty Description Part LISTÑModel NoExploded DRAWINGÑModel No 103 104 114 108 117 118 102 101 107 105 100 SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No