ProForm 831.297771 user manual Trouble-Shooting, Problem the Power does not Turn on, Top

Page 12

TROUBLE-SHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM: THE POWER DOES NOT TURN ON

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole. See step 1 on page 8.

c. Check the circuit breaker located on the treadmill

near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position.

c

 

Tripped

Reset

d

 

On

 

Position

 

PROBLEM: THE POWER TURNS OFF DURING USE

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 8.

d. Make sure that the on/off switch is in the on position.

e. If the treadmill still will not run, please call our toll-free HELPLINE.

PROBLEM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY

SOLUTION: a. Remove the six screws from the hood. Carefully re- move the hood. Locate the Reed Switch (21) and the Magnet (43) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8Ó. If nec- essary, loosen the Reed Switch Screw (76) and move the Reed Switch slightly. Retighten the Screw. Re-at- tach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8Ó

42

76

 

21

43

Top

 

View

 

12

Image 12
Contents Model No Serial No SEARS, Roebuck and CO., Hoffman ESTATES, ILTable of Contents Important PrecautionsPage Before YOU Begin Left Side Right SideAssembly Harness into the right Upright Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Console Diagram On the face of the console, remove it KeySTEP-BY-STEP Console Operation Insert the key fully into the consoleDISTANCE/LAPS CALS/FAT CalsWhen you are finished, remove the key Information ModeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETROUBLE-SHOOTING Problem the Power does not Turn onProblem the Power Turns OFF During USE TopProblem The walking belt slows when walked on Problem The walking belt is off-center when walked onProblem The walking belt slips when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Part LISTÑModel No Key No. Qty DescriptionExploded DRAWINGÑModel No 103 104 114 108 101 115 102 107 105 100 Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL