ProForm 831.299461 user manual Trouble-Shooting, Problem The power turns off during use, Top

Page 20

TROUBLE-SHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on posi- tion.

PROBLEM: The power turns off during use

c

 

Tripped

Reset

d

 

On

 

Position

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. Make sure that the on/off switch is in the on position.

e. If the treadmill still will not run, please call our toll-free HELPLINE.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the screws from the hood and carefully remove the hood. Locate the Reed Switch

(21)and the Magnet (43) on the left side of the Pulley

(42).Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8Ó. If necessary, loosen the Reed Switch Screw (30) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8Ó

42

30

 

21

43

Top

 

View

 

20

Image 20
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Page Right Side Before YOU BeginLeft Side Assembly Driver , wire cutters , and rubber malletThere may be extra screws after assembly is completed Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeCALS/FAT Cals SPEED/MIN-MILEHOW to USE Personal Trainer Programs Insert the key into the consoleSelect one of the personal trainer programs Measure your heart rate, if desiredHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Audio Adapter CableFinished, remove the key Whenkey. the program is finished, remove HOW to USE Programs Directly from OUR Internet SiteProgram Optional Chest Pulse Sensor Information MODE/DEMO ModeOptional Hand Weights HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETop TROUBLE-SHOOTINGProblem The power turns off during use Problem The walking belt slows when walked on 3ÓÐ4ÓConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LISTÑModel No Key Qty DescriptionExploded DRAWINGÑModel No 117 116 107 108 118 109 110 119 113 104 102 SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No