ProForm PFTL06711.0 warranty Troubleshooting, Symptom The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assis- tance is needed, see the front cover of this manual. SYMPTOM: The power does not turn on

a.Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly-grounded outlet (see page 14). Use only a single-outlet surge suppressor that meets all of the specifications described on page

14. IMPORTANT: The treadmill is not compati- ble with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.

b.After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.

c

Tripped

Reset

SYMPTOM: The power turns off during use

a.Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console, and then reinsert it.

d.If the treadmill still will not run, please see the front cover of this manual.

SYMPTOM: The console displays remain lit when you remove the key from the console

a.The console features a display demo mode, de- signed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 20 to turn off the demo mode.

SYMPTOM: The displays of the console do not function properly

a.Remove the key from the console and UNPLUG THE POWER CORD. Place the treadmill in the storage position (see HOW TO FOLD THE TREADMILL on page 21). Remove the two #8 x 1 1/2" Screws (52).

Then, lower the treadmill (see HOW TO LOWER THE TREADMILL FOR USE on page 21).

a

52

52

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL06711.0 Serial No On the WEBTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Part Identification Chart Assembly Wheel must turn freely Do not fully fold the Frame yet Be careful not to pinch the Upright WireFully tighten the Screws yet. Then, partially Tighten the Screws yet. Then, partially tightenNut 10. Do not overtighten the Nut Wheel must turn freely To overtighten the ScrewsConsole Wire Assembly Tie 101 Page Operation and Adjustment HOW to Plug in the Power CordConsole DiagramFeatures of the Console AudioStart the walking belt and adjust the speed HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired. Before using Select a preset workout HOW to USE a Preset WorkoutStart the workout HOW to USE the Ifit Training Mode HOW to USE the Stereo Sound SystemInformation Mode MetricHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USETroubleshooting Symptom The power turns off during useApply silicone spray or other substances to Symptom The walking belt slows when walked onStructed to do so by an authorized service rep Walking belt or the walking platform unlessPage Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyKey No. Qty Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents