ProForm PFTL12007.0 user manual Make sure that the power cord is unplugged

Page 7

1.Make sure that the power cord is unplugged.

With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (56) so that the treadmill is more stable; do not fully fold the Frame yet.

Remove and discard the two indicated bolts (A) and the shipping bracket (B).

Cut the ties securing the Upright Wire (38) to the Base (83). Locate the tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole.

Attach a Base Pad (81) to the Base (83) in the location shown with a Base Pad Spacer (13) and a 1" Tek Screw (2). Then, attach another Base Pad (81) with only a 1" Tek Screw (2).

2.Remove the 3/8" Nut (8), the 3/8" x 2" Shoulder Bolt (32), and the shipping bracket (C) from the Base (83). Attach a Wheel (84) with the Bolt and the Nut that you just removed. Do not over- tighten the Nut; the Wheel must turn freely. Discard the shipping bracket.

3.Identify the Right Upright (78) and the Right Upright Spacer (79), which are marked with stickers. Insert the Upright Wire (38) through the Right Upright Spacer as shown.

See the inset drawing. Tie the wire tie in the Right Upright (78) securely around the end of the Upright Wire (38). With the help of a second person, hold the Right Upright near the Base (83). Then, pull the other end of the wire tie until the Upright Wire is routed completely through the Right Upright.

1	B
	B	A
		A
		38
	Hole
56		81
56
		2
		Tie
		83
13
81
2
2
32
		83
	84
C
8
3
		78
38
		38
		79
		83
78

38 Wire

Tie

7

Image 7

Contents Model No. PFTL12007.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged Tighten the Nut the Wheel must turn freely Careful not to pinch the Upright WireGers do not fully tighten the Bolts yet Do not fully fold the Frame yetBolts and then tighten them Be careful not to pinch the wiresPull on the sleeve to make sure that it is locked into place Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerAvoid moving Your hands Follow your progress with the displayMeasure your heart rate if desired Stand on Foot railsFollow your progress with the display. See on HOW to USE a Personal Trainer WorkoutSelect a personal trainer workout Press the Start button to start the workoutSelect the iFIT Competition Training Center HOW to USE the Ifit Competition Training CenterEnter user information HOW to USE the Settings ModeSelect the settings mode Measure your heart rate if desired. See onOptional Chest Pulse Sensor Information ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description R0108AQty Exploded Drawing A-Model No. PFTL12007.0 R0108A Exploded Drawing B-Model No. PFTL12007.0 R0108A Exploded Drawing C-Model No. PFTL12007.0 R0108A Exploded Drawing D-Model No. PFTL12007.0 R0108A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT