4. Hold a Bolt Spacer (80) inside the lower end of | 4 |
|
|
|
the Right Upright (78). Insert a 3/8" x 4 1/2" Bolt |
| 6 |
| |
|
|
| ||
(6) with a 3/8" Star Washer (9) into the Right |
| 78 |
|
|
Upright and the Bolt Spacer. Repeat this step |
|
|
| |
|
|
|
| |
with a second Bolt Spacer (80), 3/8" x 4 1/2" |
|
|
| 9 |
Bolt (6), and 3/8" Star Washer (9). |
|
|
| |
|
|
|
| |
Hold the Right Upright Spacer (79) and the |
|
|
| 38 |
|
|
| 80 | |
Right Upright (78) against the Base (83). Be |
|
|
| |
|
|
|
| |
careful not to pinch the Upright Wire (38). |
|
|
|
|
Tighten the 3/8" x 4 1/2" Bolts (6) with your fin- |
|
|
| 80 |
gers; do not fully tighten the Bolts yet. |
|
|
| 77 |
|
|
|
| 79 |
Press a Base Endcap (77) into the Base (83). |
|
|
|
|
|
| 83 |
|
|
5. With the help of a second person, carefully tip | 5 | B |
|
|
the treadmill onto its right side. Partially fold the |
|
| ||
|
|
| ||
Frame (56) so that the treadmill is more stable; |
| A |
|
|
do not fully fold the Frame yet. |
|
|
|
|
Remove and discard the two indicated bolts (A) |
|
|
|
|
and the shipping bracket (B). |
|
|
|
|
|
| 81 |
| 56 |
Attach a Base Pad (81) to the Base (83) in the |
|
|
| |
|
|
|
| |
location shown with a 1" Tek Screw (2) and a |
| 2 |
| 32 |
Base Pad Spacer (13). Then, attach another |
|
| ||
|
|
| ||
Base Pad (81) with only a 1" Tek Screw (2). |
|
|
|
|
Remove the 3/8" Nut (8), the 3/8" x 2" Shoulder |
| 13 |
|
|
| 83 |
|
| |
Bolt (32), and the shipping bracket (C) from the |
|
|
| 84 |
Base (83). Attach a Wheel (84) with the Bolt and |
|
|
| |
| 2 | 81 | C | |
the Nut that you just removed. Do not over- |
| |||
|
|
| ||
tighten the Nut; the Wheel must turn freely. |
|
|
| 8 |
Discard the shipping bracket. |
|
|
|
|
6. With the help of a second person, hold a Bolt | 6 |
|
|
|
Spacer (80) inside the lower end of the Left |
|
|
| |
|
|
|
| |
Upright (74). Insert a 3/8" x 4 1/2" Bolt (6) with a |
| 6 |
| 74 |
3/8" Star Washer (9) into the Left Upright and |
|
| ||
|
|
|
| |
the Bolt Spacer. Repeat this step with a sec- |
| 9 |
|
|
ond Bolt Spacer (80), 3/8" x 4 1/2" Bolt (6), |
|
|
| |
|
|
|
| |
and 3/8" Star Washer (9). |
| 76 |
|
|
|
|
|
| |
Orient the Left Upright (74) and the Left Upright |
| 80 |
|
|
Spacer (76) as shown. Hold the Left Upright |
|
|
| |
|
|
|
| |
Spacer and the Left Upright against the Base |
|
|
|
|
(83). Tighten the two 3/8" x 4 1/2" Bolts (6) with |
| 80 |
|
|
your fingers; do not fully tighten the Bolts yet. |
| 77 |
|
|
|
| 83 |
|
|
Press a Base Endcap (77) into the Base (83). |
|
|
|
|
With the help of a second person, tip the tread- |
|
|
|
|
mill so that the Base (83) is flat on the floor. |
|
|
|
|
| 8 |
|
|
|