ProForm PFTL39120 user manual

Page 6

3.Insert a Plastic Shim (9) into each side of the post on the right side of the Base (38). Next, orient the Right Upright (15) as shown, and insert it into the Base. Make sure that the Wire Harness (53) does not fall into the Right Upright. Be careful to avoid pinching the Wire Harness. Note: If necessary, tap the Right Upright with a rubber mallet until it is fully seated in the Base. If the Right Upright cannot be fully seated, remove the outer Plastic Shim and then insert the Right Upright.

Attach the Right Upright (15) to the Base (38) with three 1” Bolts (16) and three 1/4” Star Washers (2). Do not tighten the Bolts yet.

Assemble the Left Upright (not shown) in the same way.

4.Hold a Handrail Spacer (3) with the arrow between the two holes pointing upward. Thread the Wire Harness (53) through the upper hole in the Handrail Spacer. Insert the Wire Harness into one of the Handrails and out of the large hole. If necessary, use needlenose pliers to pull the Wire Harness out of the hole.

Hold the Handrail Spacer (3) and the right Handrail (4) against the right Upright (15). Attach the right Handrail and the Handrail Spacer with two 3” Handrail Bolts (1) and two 5/16” Star Washers (101) as shown. Do not tighten the Handrail Bolts yet.

Attach the other Handrail (not shown) to the Left Upright

(14)as described above. Note: There is not a Wire Harness in the Left Upright.

3

 

 

53

 

 

The holes must

 

15

be on this side.

 

 

 

2

 

9

16

 

 

2

 

 

16

 

38

 

 

4

 

 

 

53

 

Large Hole

4

14

3

10115

1

53

5.Attach the end of the ground wire to the small hole in the side of the right Handrail (4) with a Silver Ground Screw (113).

Set the Console Base (87) on the Handrails (4). Thread four 3/4” Screws (5) into the Handrails and the Console Base. After you have started all four Screws, tighten the Screws until they are snug; do not overtighten the Screws.

Insert the Wire Harness (53) through the two indicated plastic ties on the Console Base (87) and then through the hole in the bottom of the Console Base.

5

87

4

53

 

 

 

4

 

 

 

Ties

5

 

113

5

 

 

 

6

Image 6
Contents QUESTIONS? Model No. PFTL39120 Serial NoCustomer HOT Line Table of Contents Important PrecautionsUnplug Treadmill before Assembly /Disassembly Back Before YOU BeginFront Right SideAssembly Make sure that the power cord is unpluggedPage Touch the right Handrail 4 to discharge any static Page Part LIST-Model No. PFTL39120 Qty DescriptionPart Identification Chart Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Console Diagram STEP-BY-STEP Console OperationInsert the key fully into the console Follow your progress with the three displays Time/Distance HOW to USE the Upper Body ArmsChange the incline of the treadmill as desired Fat Calories/CaloriesHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEMaintenance and Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Problem ONE of the Upper Body Arms Squeaks During USEExercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesExploded DRAWING-Model No. PFTL39120 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT