ProForm PFTL42105.0 user manual

Page 7

2.Orient the Right Upright (36) so that the square hole at the lower end is in the position shown. Attach the Right Upright to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet.

Attach each Wheel (45) to the Upright Base (48) with a Wheel Bolt (40), two Wheel Spacers (44), and a Nut (47) as shown. Do not overtighten the Nuts; the Wheels should turn freely.

3.Cut the tie holding the Wire Harness (28) in a bundle. Leave the large colored tie on the end of the Upright Wire.

Orient the Upright Base (48) on the Wheels (45) as shown, and center the frame assembly between the Uprights (31, 36). With the help of another person, lower the frame assembly and insert the Wire Harness (28) into the large hole at the bottom of the Right Upright (36) and out of the top.

While the frame assembly is raised, raise the Uprights (31, 36) so the Upright Base (48) is flat on the floor. Make sure that the end of the Wire Harness (28) does not fall into the Right Upright (36). It may be helpful to bend the colored tie on the end of the Wire Harness over the Right Upright.

2

36

44

 

40

 

 

 

 

47

 

 

45

45

44

 

44

 

 

 

47

 

40

 

 

 

Square Hole

 

 

39

 

48

 

 

 

40

3

 

Hole

 

 

 

 

48

 

31

 

 

 

28

 

36

45

Frame Assembly

Colored Tie

28

4.Orient the two Frame Spacers (34) as shown in the inset drawing. Open the included packet of grease and apply grease equally to both sides of each Frame Spacer.

Hold a Frame Spacer (34) between the frame assembly and the Right Upright (36). Make sure that the Frame

Spacer is oriented as shown in the inset drawing. Insert a Frame Bolt (32) through a Frame Washer (33), the Right Upright, the Frame Spacer, and the bracket on the frame assembly. Be careful not to pinch the Wire Harness (28) in the Right Upright. Finger tighten a Nut (47) onto the Frame Bolt. Do not fully tighten the Nut yet.

Repeat this step on the left side. Note: There is not a wire harness on the left side.

4

34

Left

 

28

Side

 

34

Right

 

 

 

 

Side

 

36

 

 

 

Bracket

 

 

47

 

 

33

 

34

32

 

 

 

Frame Assembly

 

7

Image 7
Contents Model No. PFTL42105.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Back Right Side Before YOU BeginMake sure that the power cord is unplugged AssemblyPage Make sure that the Wire Harness 28 does not get pinched Frame Bolts Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Start the walking belt Console DiagramSTEP-BY-STEP Console Operation Insert the key into the consoleWhenkey. you are finished exercising, remove Follow your progress with the displayMeasure your heart rate if desired Turn on the fan if desiredHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description Part LIST-Model No. PFTL42105.0R0106A Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT