ProForm PFTL29020 user manual

Page 6

3.Insert a Plastic Shim (9) into each side of the post on the right side of the Base (38). Next, orient the Right Upright (15) as shown, and insert it into the Base. Make sure that the Wire Harness (53) does not fall into the Right Upright. Be careful to avoid pinching the Wire Harness. Note: If necessary, tap the Right Upright with a rubber mallet until it is fully seated in the Base. If the Right Upright cannot be fully seated, remove the outer Plastic Shim and then insert the Right Upright.

Attach the Right Upright (15) to the Base (38) with three 1” Bolts (16) and three Star Washers (2). Do not tight- en the Bolts yet.

Assemble the Left Upright (not shown) in the same way.

4.Hold a Handrail Spacer (3) with the arrow between the two holes pointing upward. Thread the Wire Harness (53) through the upper hole in the Handrail Spacer. Next, insert the Wire Harness into a Handrail (4) and out of the indicated hole in the side of the Handrail. If neces- sary, use needlenose pliers to pull the Wire Harness out of the hole.

Hold the Handrail Spacer (3) and the Handrail (4) against the right Upright (15). Attach the Handrail and the Handrail Spacer with two Handrail Bolts (1) and 5/16” Star Washers (101) as shown. Make sure that the Wire Harness (53) is not in the way of the Handrail Bolts. Do not tighten the Handrail Bolts yet.

Attach the other Handrail (not shown) to the Left Upright

(14)as described above. Note: There is not a Wire Harness in the Left Upright.

3

 

53

 

The holes must

15

be on this side.

 

2

9

16

2

 

16

38

 

4

 

53

 

4

 

14

3

 

101

15

1

53

 

5.Set the Console Base (87) on the Handrails (4). Thread four 3/4” Screws (5) into the Handrails and the Console Base. After you have started all four Screws, tighten the Screws until they are snug; do not overtighten the Screws.

Insert the Wire Harness (53) through the two indicated plastic ties on the Console Base (87) and then through the hole in the bottom of the Console Base.

5

87

4

 

4

 

 

53

5

 

Ties

 

 

 

5

 

6

Image 6
Contents QUESTIONS? Model No. PFTL29020 Serial NoCustomer HOT Line Table of Contents Important PrecautionsShock Back Before YOU BeginFront Right SideAssembly Make sure that the power cord is unpluggedPage Touch the Right Handrail 59 to discharge any static Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt AA batteries Diagram of the ConsoleBattery Installation STEP-BY-STEP Console OperationHOW to Change the Incline of the Treadmill CALS/FAT CalsHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEMaintenance and Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesExercise Frequency Suggested StretchesOrdering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part Identification Chart Part LIST-Model No. PFTL29020 Qty DescriptionPFTL29020