ProForm FTL59106.0 user manual Connectors are not Connected

Page 9

8. While a second person holds the console as-

8

 

Console

sembly near the Pulse Bar (66), connect the

 

 

 

Assembly

Ground Wire (107) on the Pulse Bar to the

 

 

 

 

 

ground wire from the console assembly.

 

 

 

Connect the wire from the console assembly to

Ground

 

75

the Upright Wire (75). Make sure to connect

 

the connectors properly (see the inset draw-

Wire

 

 

 

 

 

ing). The connectors should slide together

 

 

 

easily and snap into place. If the connectors

 

 

 

do not slide together easily and snap into place,

 

 

107

turn one connector and then try again. IF THE

 

 

CONNECTORS ARE NOT CONNECTED

 

 

Wire

PROPERLY, THE CONSOLE MAY BE DAM-

 

66

75

AGED WHEN THE POWER IS TURNED ON.

 

Lay the wires inside the bottom of the Pulse Bar

 

 

76

(66).

 

 

 

 

 

9. Set the console assembly on the Left and Right

9

 

 

Uprights (70, 76). Be careful not to pinch any

 

Console Assembly

 

 

wires.

 

 

 

Attach the console assembly to the Pulse Bar

 

 

 

(66) with six 3/4" Screws (23). Start all six

 

 

 

Screws, before tighten them yet.

 

 

 

 

 

 

66

 

 

 

 

23

23

23

 

 

 

76

 

 

70

10.Identify the Left Handrail Cover (68), which has

10

 

 

 

 

a LEFT sticker on it. Slide the Left Handrail

Console

 

 

 

 

 

 

 

Cover onto the left Handrail (62) and up against

 

Assembly

 

 

 

the console assembly. Tighten two Cover

 

 

 

 

 

Screws (52) into the Left Handrail Cover and the

 

68

 

 

 

Left Upright (70); be careful not to overtighten

 

 

 

 

 

62

 

 

 

the Cover Screws.

 

 

 

 

Attach the Right Handrail Cover (74) in the same

 

 

 

 

 

way.

 

 

 

 

 

 

 

52

70

 

 

 

 

 

 

74

 

 

 

 

62

 

 

 

 

 

52

76

 

 

 

 

 

 

9

 

 

 

 

Image 9
Contents QUESTIONS? Model No. PFTL59106.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedDo not tighten the Upright Bolts yet Do not tighten the Upright Bolts yet See steps 2 and 4. Fully tighten the two Endcap ScrewsTighten the Bolts yet Connectors are not Connected Page Small Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerFollow your progress with the display Measure your heart rate if desiredWhenkey. you are finished exercising, remove HOW to USE a Preset Program Select one of the preset programsInsert the key fully into the console Press the Start button to start the program HOW to USE a Calorie ProgramFollow your progress with the display Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Page Key Qty Description R0806BExploded Drawing A-Model No. PFTL59106.0 R0806B Exploded Drawing B-Model No. PFTL59106.0 R0806B Exploded Drawing C-Model No. PFTL59106.0 R0806B Exploded Drawing D-Model No. PFTL59106.0 R0806B Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT