ProForm 590 QS user manual Trouble-Shooting, Problem The power turns off during use, Top

Page 16

TROUBLE-SHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole. See step 1 on page 10.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position.

PROBLEM: The power turns off during use

c

 

Tripped

Reset

d

 

On

 

Position

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 10.

d. Make sure that the on/off switch is in the on position.

e. If the treadmill still will not run, please call our toll-free HELPLINE.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the screws from the hood and carefully remove the hood. Locate the Reed Switch

(21)and the Magnet (43) on the left side of the Pulley

(42).Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8Ó. If necessary, loosen the Reed Switch Screw (76) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8Ó

42

76

 

21

43

 

Top

 

View

 

16

Image 16
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Page Before YOU Begin Left Side Right SideAssembly Your own phillips screwdriverExtension Legs 103 remain in the Uprights HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Console Diagram Features of the ConsoleHOW to USE the Manual Mode STEP-BY-STEP Console OperationTIME/MIN-MILE CALS./FAT CalsPulse displayÑThis Speed displayÑThisTo connect the tread- mill to a home stereo Measure your pulse, if desired Information Mode Important The Cals FAT CALS./PULSE displayHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TROUBLE-SHOOTINGTop Problem The walking belt slows when walked on 3ÓÐ4ÓExercise Intensity Conditioning GuidelinesWorkout Guidelines Part LISTÑModel No Key Qty DescriptionExploded DRAWINGÑModel No 107 108 109 102 101 110 103 104 105 100 Model No Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL