ProForm PFEVEL2786.0 Handlebars are on the correct sides, Onto each end of the Handlebar Axle

Page 8

8. Slide the Left and Right Handlebars (7, 9) onto the

Handlebar Axle (33). Make sure that the

Handlebars are on the correct sides.

Using the included pedal tool, tap a Push Nut (78)

 

onto each end of the Handlebar Axle (33).

Make

sure that

the Push Nuts are turned as shown in

 

the inset

drawing.

(Note: It may be helpful if anoth-

er person holds a block of wood against one end of the Handlebar Axle while you tap a Push Nut onto the other end.) Then, tap a Large Axle Cap (49) onto each end of the Handlebar Axle.

9.Identify the Left Link Arm (15), which is marked with a sticker.

Apply a small amount of grease to an M8 x 77mm

Button Bolt (58). Insert the Button Bolt into the Left Handlebar Base (8). Slide an M8 Flat Washer (73),

a Link Arm Bushing (45), the Left Link Arm (15), and

another

M8 Washer (73) onto the Button Bolt.

Make

sure

that the Link Arm

Bushing and the Left

 

Link

Arm

are turned as

shown.

Tighten an M8

Nylon Locknut (66) onto the Button Bolt. Rest the notch in the Left Link Arm on the left lock rod.

Attach the Right Link Arm (not shown) to the Right

Handlebar Base (not shown) in the same way.

10.Remove the 1/2” Pedal Nut (68) from the shaft of one of the Pedals (23). Make sure that there is a Pedal Spring (42), a Red Washer (71), a Pedal Bushing (43), a Black Pedal Washer (79), and a Pedal Spacer (44) on the shaft of the Pedal. In addi- tion, make sure that the Pedal Bushing (43) is turned as shown. Firmly tighten the shaft of the Pedal clockwise into the left Crank Arm (26).

Tighten the 1/2” Pedal Nut (68) back onto the shaft.

Attach the other Pedal (not shown) in the same way.

8

 

9

 

 

1

 

 

 

49

 

33

 

7

 

 

 

78

 

 

 

49

 

 

 

 

Pedal Tool

78

33

9

 

 

 

 

66

 

 

8

73

 

 

 

 

 

73

45

15

 

58

 

 

 

Grease

 

 

 

Lock

Notch

 

 

Rod

 

 

10

 

 

 

 

26

 

 

 

68

 

 

42

44

 

 

 

 

 

 

79

 

 

71

43

 

 

 

 

 

23

 

 

 

11.Make sure that all parts are properly tightened before you use the exercise cycle. Place a mat beneath the exercise cycle to protect the floor.

8

Image 8
Contents Serial Number Decal Patent PendingTable of Contents Important Precautions Tions before using the exercise cycleBefore YOU Begin FrontBack Right SideRecommended AssemblyAssembly requires two persons Set the Upright 2 on the Frame Switch WireAny slack Battery compartment Handlebars are on the correct sides Onto each end of the Handlebar AxleDrawing Shown Tighten an M8Dual-action Mode Stationary ModeHandlebar Operation Description of the ConsoleSteadily Battery InstallationHOW to Operate the Console Adjusting the Reed Switch Console TroubleshootingAdjusting the Belt Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Toe Touch StretchHamstring Stretch Calf/Achilles StretchExploded DRAWING-Model No Description Key No. QtyR1102A 6673SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyWhirlwind