ProForm PFEL29222 user manual Maintenance and Troubleshooting, Battery Replacement

Page 12

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the elliptical crosstrainer regularly. Replace any worn parts immediately.

To clean the elliptical crosstrainer, use a damp cloth and a small amount of mild dish soap. Important:

Keep liquids away from the console and keep the console out of direct sunlight. During storage, remove the batteries from the console.

BATTERY REPLACEMENT

If the console display becomes dim, the batteries should be replaced. See assembly steps 3 and 4 on page 6 for replacement instructions.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted. To do this, you must remove the Pedal Springs (11), the right Pedal Disc (15), and the Side Shields (3, 4). See step 8 on page 8 and remove the Pedal Springs.

 

 

15

64

 

4

11

3

 

 

 

51

52

 

 

 

 

 

41

 

 

 

11

64

 

 

 

 

 

 

51

 

 

41

52

 

 

51

 

 

64

 

 

 

Next, remove the four Screws (51) from the right Pedal Disc (15), and slide the Pedal Disc off. Remove all Screws (52, 64) from the Right Side Shield (4) and the two Bolts (41) from beneath the Pedal Disc, and remove the Right Side Shield (4). Remove all Screws

(52)from the Left Side Shield (3), and remove the Left Side Shield.

Next, see the drawing below and locate the Reed Switch (53). Loosen, but do not remove, the indicated M4 x 16mm Self-tapping Screw (52). Slide the Reed Switch slightly toward or away from the Magnet (58) on the flywheel. Retighten the Screw. Turn the left Pedal Disc (15) for a moment. Repeat until the console dis- plays correct feedback. When the Reed Switch is cor- rectly adjusted, reattach the Side Shields (3, 4), the right Pedal Disc (15), and the Pedal Springs (11).

58

53

15

52

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling, even when the resistance is adjusted to the highest level, the Drive Belt (19) may need to be adjusted. To adjust the Drive Belt, you must first remove both side shields. See HOW TO ADJUST THE REED SWITCH at the left and remove the side shields.

Next, loosen

 

 

the M8 x

 

 

22mm Flat

 

 

Head Screw

 

 

(68) and turn

 

 

the M10 x

 

 

60mm Bolt

68

 

(62) until the

 

 

 

Drive Belt (19)

 

 

is tight. When

62

 

the Drive Belt

19

 

is tight, tighten

 

 

the Flat Head

 

 

Screw. Reattach the side shields.

12

Image 12
Contents QUESTIONS? Model No. PFEL29222 Serial NoCustomer HOT Line Table of Contents Important Precautions Before YOU Begin FrontBack Left SideAssembly Wrench A rubber malletWires and cables Make sureDo not get PinchedMake sure that the Handlebars are on the correct sides Page HOW to USE the Elliptical Crosstrainer HOW to Exercise on the Elliptical CrosstrainerHOW to Adjust the Pedals Features of the Console HOW to Operate the ConsoleScan mode Page Maintenance and Troubleshooting Battery ReplacementHOW to Adjust the Reed Switch HOW to Adjust the Drive BeltConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PFEL29222 Qty DescriptionR1204A HOW to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT