ProForm PFEL29222 user manual Make sure, Wires and cables, Do not get, Pinched, This step

Page 6

2.While another person lifts the back of the Frame (1), attach the Rear Stabilizer (9) to the Frame with two M10 x 75mm Carriage Bolts (34) and two M10 Nylon Locknuts (33).

3.The Console (23) requires three “AA” batteries (not included); alkaline batteries are recommended. Insert three batteries into the battery compartment. Make sure that the batteries are oriented as shown by the diagram inside the battery compartment.

4.While another person holds the Console (23) in the position shown, insert the control cable and the con- sole wire down through the Upright (2). Attach the ground wire to the Upright with an M4 x 16mm Screw (52). Insert the excess cable and wire into the Upright.

Attach the Console (23) to the Upright (2) with four M4 x 16mm Screws (52). Be careful to avoid pinching the cable and wires.

Make sure that the Resistance Knob (42) is turned to the lowest setting before proceeding.

5.While another person holds the Upright (2) in the posi- tion shown, connect the console wire to the Reed Switch Wire (53).

Next, connect the control cable to the Resistance Cable (43) in the following way:

See drawing A. Pull up on the metal bracket, and insert the tip of the control cable into the wire clip on the Resistance Cable (43) as shown.

See drawing B. Firmly pull the control cable and slide it into the metal bracket on the Resistance Cable (43) as shown.

See drawing C. Using pliers, squeeze the prongs on the upper end of the metal bracket together.

Push the excess cable and wires down into the Frame

(1). Insert the Upright (2) into the Frame. Do not pinch the wires or cables. Secure the Upright to the Frame with two M10 x 76mm Button Bolts (7), two M10 Split Washers (45), and two M10 Nylon Locknuts (33). Do not tighten the Bolts yet.

6

2

 

 

33

 

 

 

 

 

 

9

 

33

 

 

 

 

1

 

 

 

 

34

3

 

 

 

 

 

 

Batteries

23

 

 

 

4

 

23

 

 

 

 

42

Console Wire

 

52

 

 

 

 

52

Control Cable

Ground Wire

52

 

 

 

2

 

 

5

2

 

Make sure the

 

 

 

 

45

wires and cables

 

 

do not get

 

 

7

33

 

pinched and

 

 

damaged during

 

 

 

Control

 

 

this step.

 

Console

 

Cable

 

 

 

Wire

 

 

 

 

43

 

53

 

 

 

 

1

 

 

 

A

 

B

C

Metal

 

 

Control

Bracket

 

 

 

 

Cable

 

 

 

Control

 

Control

 

Cable

Cable

 

 

 

 

43

 

43

43

Image 6
Contents QUESTIONS? Model No. PFEL29222 Serial NoCustomer HOT Line Table of Contents Important Precautions Back Before YOU BeginFront Left SideAssembly Wrench A rubber malletDo not get Wires and cablesMake sure PinchedMake sure that the Handlebars are on the correct sides Page HOW to USE the Elliptical Crosstrainer HOW to Exercise on the Elliptical CrosstrainerHOW to Adjust the Pedals Features of the Console HOW to Operate the ConsoleScan mode Page HOW to Adjust the Reed Switch Maintenance and TroubleshootingBattery Replacement HOW to Adjust the Drive BeltWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFEL29222 Qty DescriptionR1204A HOW to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT