ProForm PFSY6806.0 Assembly, Make Things Easier for Yourself, Locknut the Wheel must pivot easily

Page 5

ASSEMBLY

Make Things Easier for Yourself

Everything in this manual is designed to ensure that the weight system can be assembled suc- cessfully by almost anyone. However, the weight system has many parts and the assembly process will take time. By setting aside plenty of time, assembly will go smoothly.

To hire an authorized service technician to assem- ble the weight system, call toll-free 1-800-445-2480.

Before beginning assembly, carefully read the following information and instructions:

Assembly requires two people.

Because of its weight and size, the weight sys- tem should be assembled in the location where it will be used. Make sure that there is enough clearance to walk around the weight system as you assemble it.

Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

Tighten all parts as you assemble them, unless instructed to do otherwise.

As you assemble the weight system, make sure all parts are oriented as shown in the drawings.

For help identifying small parts, use the PART IDENTIFICATION CHART.

In addition to the included grease packet and

hex key , assembly may require the fol- lowing tools (not included):

• Two adjustable wrenches

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

• Clear tape or masking tape, and soapy water

Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

1.

Before beginning assembly, make sure you understand the information in the box above. For help identifying small parts, use the PART IDENTIFICATION CHART in the center of this manual.

Attach a Wheel (32) to a Wheel Cap (31) with an M8 x 65mm Button Bolt (94) and an M8 Nylon Locknut (110). Do not overtighten the Nylon

Locknut; the Wheel must pivot easily.

Attach the Wheel Cap (31) to the Base (1) with two M4 x 16mm Self-tapping Screws (99).

Repeat this step with the other Wheel Cap (31).

2.Attach a Locking Caster (76) to the Base (1) with four M8 x 20mm Button Bolts (92) and four M8 Nylon Locknuts (110).

Repeat this step with the other Locking Caster (76).

1

 

 

 

 

99

 

1

 

 

 

 

 

 

94

 

 

 

 

31

110

99

 

 

32

 

 

 

 

 

 

 

 

31

2

 

 

92

 

 

 

76

92

 

 

 

 

76

 

 

 

1

 

 

 

 

110

 

5

Image 5
Contents Model No. PFSY6806.0 Serial No QUESTIONS?Call TOLL-FREE Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Left Side Before YOU BeginRight Side Make Things Easier for Yourself AssemblyLocknut the Wheel must pivot easily Repeat this step with the other Wheel CapPage Tighten the M10 Nylon Locknuts 108 used in steps 3 Locknut yet108 Page Page Repeat this step on the other side of the Dip Arm Repeat this step for the Seat Frame Adjusting the DIP Handles AdjustmentsAdjusting the Press ARM Adjusting the DIP ARMAttaching the Pulley Housings Adjusting the SeatAttaching the Curl PAD Attaching the LEG DeveloperAttaching the Handles Attaching the Curl BARAttaching the Squat BAR Adjusting the Cable Moving the Weight SystemChanging the Weight Setting Weight Weight Resistance ChartCable Diagram Exercise Guidelines Staying Motivated Muscle ChartCooling Down Key Qty Description R0906AM10 x 55mm Carriage Bolt Part Identification ChartExploded Drawing A-Model No. PFSY6806.0 Exploded Drawing B-Model No. PFSY6806.0 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty