ProForm 831.23743.1 Maintenance and Troubleshooting, Battery Replacement, HOW to Adjust the Belt

Page 19

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. Important: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

BATTERY REPLACEMENT

If the console displays become dim, the batteries should be replaced; most console problems are the result of low batteries. See assembly step 5 on page 8 for replacement instructions.

HANDGRIP PULSE SENSOR TROUBLESHOOTING

If the handgrip pulse sensor does not function proper- ly, see step 5 on page 16.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted. First, remove all of the screws from both side shields; there are three sizes of screws in the side shields—note which size of screw you remove from each hole. Then, gently pry the side shields away from the frame.

Next, locate the

 

 

 

Reed Switch (58).

 

 

 

Turn the Left

58

41

26

Pedal Disc (26)

 

84

 

until the Magnet

 

 

(41) is aligned

 

 

 

with the Reed

 

 

 

Switch. Loosen,

 

 

 

but do not

 

 

 

remove, the indi-

 

 

 

cated M4 x

 

 

 

16mm Screw

 

 

 

(84). Slide the

 

 

 

Reed Switch slightly closer to or away from the Magnet, and then retighten the Screw. Rock the Left Pedal Disc forward and backward just enough that the Magnet passes the Reed Switch repeatedly. Repeat

until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the side shields. Note: If you have questions as to which screw should be in which hole, see EXPLODED DRAWING B on page 27 and the PART LIST on page 24.

HOW TO ADJUST THE BELT

If you can feel the pedals slip while you are pedaling, even when the resistance of the pedals is at the high- est setting, the Belt (46) may need to be adjusted.

First, remove all the screws from both side shields; there are three sizes of screws in the side shields—note which size of screw you remove from each hole. Then, gently pry the side shields away from the frame.

Next, turn the

 

Belt Adjustment

 

Screw (72) until

46

the Belt (46) is

 

tight. Then, reat-

 

tach the side

 

shields. Note: If

 

you have ques-

 

tions as to which

72

screw should be

in which hole, see

 

EXPLODED

 

DRAWING B on page 27 and the PART LIST on page 24.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Before YOU Begin Screw Flat Head 95-2 Bolt M10 x 70mm Button Screw AssemblyRepeat this step to attach the other Wheel Avoid pinching Wire Harness During this step Tip Be careful not to pinch the wires during this step Repeat this step on the right side Elliptical exerciser Leg 6 in the same way Grease HOW to Move the Elliptical Exerciser HOW to USE the Elliptical ExerciserHOW to Exercise on the Elliptical Exerciser HOW to Adjust the Stride of the Elliptical Exerciser Console Diagram Features of the Console Select the manual mode HOW to USE the Manual ModeLower middle Turn on the fan if desired Turn on the console. See on Select a target tone workout HOW to USE a Target Tone WorkoutBegin pedaling to start the workout Turn on the console. See on Select a preset workout HOW to USE a Preset WorkoutHOW to Adjust the Reed Switch Maintenance and TroubleshootingBattery Replacement Handgrip Pulse Sensor TroubleshootingExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Page Key No. Qty Description Part LIST-Model NoQty Description Exploded Drawing Get it fixed, at your home or ours DAY Full Warranty
Top Page Image Contents