Impex SM-4008 manual Diagram

A.) Attach the two Cross-over Swivel Pulley Brackets (#10) to left and right Upper Side Frame (#7). Secure each Bracket with four M8 x 3/8” Allen Bolts (#101) and four Ø 5/8” Washers (#106).

B.) Remove the U-shaped Connector, Big Washer, and Ball Stopper from one end of 266” Upper Cable (#47).

C.) Attach a Pulley (#62) to the left Swivel Bracket and secure it with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110).

D.) Insert the end of Cable through the left Cross-over Swivel Pulley Bracket (#10). Draw the Cable over the Pulley and pull it towards the back of the machine.

E.) Attach a Cable Roller (#42) to the left Cross-over Swivel Pulley Bracket (#10). Secure it with one M8 x 1 5/8” Allen Bolt (#102), two Ø 5/8” Washers (#106), and one M8 Aircraft Nut (#109).

F.) Attach a Small Pulley (#63) to the opening on the left Upper Side Frame. Secure it with one M10 x 2 ¾” Allen Bolt (#97), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). Draw the Cable around the top of the Small Pulley.

G.) Attach another Small Pulley (#63) to the opening next to the Small Pulley installed in F. Repeat F to install the Small Pulley. Draw the Cable under the Small Pulley to an open

	pulley shaft.
H.) Attach a Pulley (#62) to the open pulley shaft. Secure it with one M10 x 1 ¾” Allen Bolt
	(#93), one Ø ¾” Washer (#107), and one Cable Retainer (#78).
I.)	Draw the Cable around the Pulley then to an open pulley shaft on Rear Upper Frame (#18).
	Attach a Pulley to the open shaft. Secure it with one M10 x 2 ¾” Allen Bolt (#97), two Ø ¾”
	Washers (#107), one Cable Retainer (#78), and one M10 Aircraft Nut (#110).
J.)	Draw the Cable around the Pulley and to the open bracket on the Rear Upper Frame (#18).
	Attach a Pulley to the bracket. Secure it with one M10 x 5” Allen Bolt (#99), one Cable

Retainer (#78), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110).

K.) Draw the Cable around the Pulley and downward. Attach a Pulley to a Single Floating Pulley Bracket (#34). Secure the Pulley with one M10 x 2” Allen Bolt (#94), two Ø ¾” Washers (#107), two Cable Retainers (#78), and one M10 Aircraft Nut (#11). Draw the Cable upward to the open bracket one the other side on Rear Upper Frame (#18). Let the Pulley hanging for now.

L.) Remove the Nut and Washer installed in J. Attach a Pulley onto the Allen Bolt (#99), then attach a Cable Retainer (#78) to the Pulley, and secure with the removed Washer and Nut.

M.) Draw the Cable to open shaft on Rear Upper Frame. Repeat I to install a Pulley. N.) Draw the Cable to an open pulley shaft. Repeat H to install a Pulley.

O.) Draw the Cable to the opening on the right Upper Side Frame. Repeat F to install two Small Pulleys #63).

P.) Draw the Cable through the right Cross-over Swivel Pulley Bracket. Repeat E to install a Cable Roller (#42).

Q.) Re-install the Ball Stopper; Big Washer, and the U-shaped Connector previously removed in A above. Connect a Single Handle (#79) to each end of the Cable with a Hook (#73). Secure each Hook with one M10 x 1 1/8” Allen Bolt (#92) and M10 Aircraft Nut (#110).

17

DIAGRAM 7-1