Diamondback 06.DB SS OM manual Removing a Quick Release Rear Wheel

Page 32

(5)If the lever cannot be pushed all the way to a position parallel to the fork blade, return the lever to the OPEN position. Then turn the tension adjusting nut counterclockwise one- quarter turn and try tightening the lever again.

(6)Re-engage the brake quick-release mechanism to restore correct brake pad-to-rim clearance; spin the wheel to make sure that it is centered in the frame and clears the brake pads; then squeeze the brake lever and make sure that the brakes are operating correctly.

! WARNING: Secondary retention devices are not a substitute for correct quick release adjustment. Failure to properly adjust the quick release mechanism can cause the wheel to wobble or disengage, which could cause you to loose control and fall, resulting in serious injury or death.

c. Removing a Quick Release Rear Wheel

(1)Shift the rear derailleur to high gear (the smallest, outermost rear sprocket).

(2)If your bike has rim brakes, disengage the brake’s quick- release mechanism to open the clearance between the wheel rim and the brake pads (see Section 4.A, fi gs. 7 through 10).

(3)Pull the derailleur body back with your right hand.

(4)Move the quick-release lever to the OPEN position (fi g. 20b).

(5)Lift the rear wheel off the ground a few inches and, with the derailleur still pulled back, push the wheel forward and down until it comes out of the rear dropouts.

d.Installing a Quick Release Rear Wheel

NOTE: If your bike is equipped with disk brakes, be careful not to damage the disk, caliper or brake pads when re-inserting

the disk into the caliper. Never activate a disk brake’s control lever unless the disk is correctly inserted in the caliper.

(1)Shift the rear derailleur to its outermost position

(2)Pull the derailleur body back with your right hand.

(3)Move the quick-release lever to the OPEN position (see fi g. 20a & b). The lever should be on the side of the wheel opposite the derailleur and freewheel sprockets.

(4)Put the chain on top of the smallest freewheel sprocket. Then, insert the wheel into the frame dropouts and pull it all the way in to the dropouts.

(5)Tighten the quick-release adjusting nut until it is fi nger tight against the frame dropout; then swing the lever toward the front of the bike until it is parallel to the frame’s chainstay or seatstay and is curved toward the wheel (fi g. 20b). To apply enough clamping force, you should have to wrap your fi ngers around a frame tube for leverage, and the lever should leave a clear imprint in the palm of your hand.

! WARNING:Securelyclampingthewheeltakesconsiderable force. If you can fully close the quick release without wrapping your fi ngers around the seatstay or chainstay for leverage, and the lever does not leave a clear imprint in the palm of your hand, the tension is insuffi cient. Open the lever; turn the tension adjusting nut clockwise a quarter turn; then try again

(6)If the lever cannot be pushed all the way to a position parallel to the chainstay or seatstay tube, return the lever to the OPEN position. Then turn the adjusting nut counterclockwise one-quarter turn and try tightening again.

(7)Push the rear derailleur back into position.

(8)Re-engage the brake quick-release mechanism to restore correct brake pad-to-rim clearance; spin the wheel

30

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Page Serial Number Locations For BMX and other single-speed bicycles Read it before you take the fi rst ride on your new bicycleGeneral Warning Special note for parentsContents Safety fi rst Mechanical Safety CheckFirst Bike fi tHandlebar and saddle alignment Make sure the saddle First rideSafety Riding SafetyWear safety gear appropriate to the kind of riding you plan Wet Weather Riding Night RidingBicycling in Traffi c Downhill, Stunt or Competition BikingChanging Components or Adding Accessories FitStandover height Saddle positionHandlebar height and angle Brakes TechBrake reach Hand Brakes How hand brakes work Adjusting your coaster brakeCoaster Brake How the coaster brake works Page Wheels Front Wheel Secondary Retention Devices Removing a Bolt-On Front WheelRemoving a Bolt-On Rear Wheel with Hand Brake Installing a Bolt-On Front WheelInstalling a Bolt-On Rear Wheel with Hand Brake Installing a Bolt-On Rear Wheel with Coaster Brake PedalsWhich may cause you to lose control and fall Tires and Tubes Service Tire ValvesService Intervals Before every ride Mechanical Safety CheckIf your bicycle sustains an impact Appendix a LessonsDriveway Rideout Turning Without WarningFollowing the Leader SummaryAppendix B Page Appendix C Installing a Quick Release Front Wheel Installing a Quick Release Rear Wheel Removing a Quick Release Rear WheelSeatpost Quick Release Raleigh America, Inc. Bicycle Limited Warranty Free Lost & Found Service Price paid Marketing Services Raleigh America, Inc
Top Page Image Contents