PYLE Audio PFTL31404.1 user manual Troubleshooting, Problem The power turns off during use, Top

Page 15

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call the toll-free telephone number on the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 10. Important: The treadmill is not com-

patible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

2

2

POWER CORD. Remove the Screws (2) from the

Hood (1), and carefully pivot the Hood off.

 

 

 

 

 

1

2

 

 

 

Locate the Reed Switch (10) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (26), move the Reed Switch slightly, and then retighten the Screw. Re-attach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8”

17

10

18

26

Top

 

View

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model No. PFTL31404.1 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedFold the treadmill until it is completely assembled Right Upright be careful not to damage the Upright Wire Pinch the Upright Wire. Firmly tighten the BoltsBolts 37. Firmly tighten the Bolts Small Hole Top View Do not overtighten the ScrewsOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Insert the key into the consoleChange the incline of the treadmill as desired Turn on the fan if desired When you are finished exercising, remove the keyFollow your progress with the track and the displays Measure your heart rate if desiredHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useTop Belt has shifted to the left, use the allen wrench to Problem The walking belt slows when walked onUnplug the Power CORD. If the walking Key and Unplug the Power Cord . UsingExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Qty Description Key Qty DescriptionExploded DRAWING-Model No. PFTL31404.1 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents