ProForm 831.29948 Trouble-Shooting, Check the on/off switch located on the treadmill near

Page 20

TROUBLE-SHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that is4_IL1449. listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation. of 450 joules. The surge suppressor must be electdcally rated for 120 volts AC and 15 amps.

Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill

near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

_C

Tripped _

Reset

d. Check the on/off switch located on the treadmill near

Jd

Positionj

the power cord. The switch must be in the on posi-

 

tion.

 

 

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above), if the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. Make sure that the on/oft switch is in the on position.

e. If the treadmill still will not run, please call our toll-free HELPLINE.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the screws from the hood and carefully remove the hood. Locate the Reed Switch

(21)and the Magnet (43) on the left side of the Pulley

(42).Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 118". If necessary, loosen the Reed Switch Screw (76) and

move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

l/8"-----

/

I II I

2O

Image 20
Contents Elplin Bearb RoebuckPatent Pending Hoffman EstatesPRO.FORM 8 3 5 Q T Important Precautions Page Not included Lock KnobLeft Side Right SideAssembly Post Plastic TieHOW to Plug in the Power Cord Performant Lube TM Walking BeltConsole Diagram Features of the ConsoleHOW to Turn on the Power Select the manual modeLocate the on/off FollowCALS. FAT¢ALG SPEED/MIN-MILESpeed MA+ Insert the key into the consoleHOW to Connect Your Portable CD Player HOW to Connect Your Portable StereoHOW to Connect Your Home Stereo HOW to Connect YoUR OmputerWire removed from StereoHOW to Connect Your VCR Insert the key fully into the consoleStopped by pressing the Stop button on your CD payer or VCR Measure your heart rate, if desired See onPage Optional Hand Weights Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETROUBLE-SHOOTING Check the on/off switch located on the treadmill nearPage Exercise Intensity Workout GuidelinesRosa Exploded Save the Exploded Drawing For Future Reference11o Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Part No R0800A