12. Pull the upper cable (B), which is attached inside | 12 |
|
|
|
of the Mech Assembly (6), up between the |
|
|
| |
|
|
| B | |
Upright (3) and the Pulley Plate (18). |
|
|
| |
| 85 |
| ||
|
|
| ||
Attach another Large Pulley (17) between the |
| 54 |
|
|
|
|
|
| |
Upright (3) and Pulley Plate (18) with an M12 x |
|
|
|
|
62mm Button Bolt (80) and an M12 Nylon |
|
| 72 |
|
Locknut (72). Make sure that the upper cable | 80 |
|
| |
|
|
| ||
(B) is between the two Pulleys. |
|
|
| |
|
|
| 17 | |
|
| 18 |
| |
|
|
|
| |
Hold the 1 1/2” Spacer (54) inside of the loop of | 3 |
|
|
|
the upper cable (B), and between the Upright (3) | 6 |
|
|
|
|
|
|
| |
and the Pulley Plate (18). Attach the Spacer with |
|
|
|
|
a 3/8” x 2 1/4” Screw (85). Make sure the ends |
|
|
|
|
of the cable do not wrap around each other | 13 |
|
|
|
below the Spacer and the Large Pulleys (17) |
|
|
| |
| 83 |
|
| |
used in steps 11 and 12 (see the CABLE DIA- |
|
|
| |
| 55 |
|
| |
GRAM on page 18). |
|
|
| |
| 57 |
|
| |
|
|
|
| |
Tighten the M12 Nylon Locknuts (72) used in | 56 |
|
|
|
|
|
|
| |
steps 11 and 12. |
| Metal |
| 83 |
|
| Cover | 75 | |
13. Attach a Small Guide Spacer (56), a Large Guide |
|
| ||
|
|
|
| |
Spacer (57), and two Bar Guides (55) to the Lat | 55 |
|
|
|
Tower (5) with a 3/8” x 6” Bolt (83). Do not tight- |
|
|
| |
5 |
|
|
| |
en the Bolt yet. |
|
| 61 |
|
|
|
|
| |
Pull the upper cable (B) up between the Bar |
|
|
|
|
Guides (55). Press the metal cover on the cable |
| B |
|
|
into the groove in the Block Spacer (58). Attach a | 56 | 58 |
|
|
Small Guide Spacer (56), the Block Spacer, the |
|
|
|
|
two Bar Guides, a 3/8” SAE Washer (75), and the |
|
|
|
|
two Tethers (61) to the Lat Tower (5) with another |
|
|
|
|
3/8” x 6” Bolt (83). Do not tighten the Bolt yet. | 14 |
|
|
|
| 55 |
|
|
|
14. Insert the Resistance Bar (9) between the Bar |
| 61 |
|
|
Guides (55), and center it on the Block Spacer |
|
|
| |
|
|
|
| |
(not shown). |
|
|
|
|
Press a Pulley Bracket (10) onto the Resistance |
|
|
| 73 |
|
|
|
| |
Bar (9). Attach a Tether (61) to the Pulley Bracket |
| 9 |
|
|
at the upper hole, with a 3/8” x 2 3/4” Bolt (93), a |
|
|
| |
3/8” SAE Washer (75), and a 3/8” Nylon Locknut |
|
|
| 75 |
(73). |
|
| 10 |
|
|
|
|
| |
Repeat on the other side of the Resistance |
| 93 |
|
|
|
|
|
| |
Bar (9). Then, tighten the 3/8” x 6” Bolts (83) |
|
|
|
|
used in step 13. | 15 |
|
|
|
|
|
|
| |
15. Hold a Large Pulley (17) inside of the upper cable | 10 | 72 |
|
|
|
|
|
| |
(B). Attach the Pulley to a Pulley Bracket (10) |
|
|
|
|
with an M12 x 58mm Button Bolt (81) and an M12 | 81 |
|
|
|
Nylon Locknut (72). Make sure that the cable is |
|
|
| |
|
|
|
| |
routed as shown in the CABLE DIAGRAM on |
|
|
|
|
page 18. |
|
|
|
|
| 17 | B |
|
|
|
|
|
| |
11