JVC CA-MXDVA9 Changing the Display Settings, Press Cursor 3 or 2 to adjust the output level, then

7Adjusting the center and rear speaker output levels

You can adjust the speaker output level for the center speaker and rear speakers.

You can adjust the output level while listening to the test tone.

•Make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

•To output test tone properly, turn off the sound mode and the DSP Surround mode before entering on-screen menu.

1Display EXPERT SPEAKER SETTING menu.

• See page 38.

2 Press Cursor (5 / ∞ / 3 / 2) to move	to “TEST
TONE,” then press ENTER.

“TEST TONE” changes its color to green and test tone comes out of in the following sequence—left front speaker, center speaker, right front speaker, right rear speaker, and left rear speaker.

•Test tone is output only when the tray loaded with a DVD is selected.

3 Press Cursor (5 / ∞ / 3 / 2) to move to “C.SPK–

LEVEL” or “R.SPK–LEVEL,” then press ENTER.

4Press Cursor 3 or 2 to adjust the output level, then press ENTER.

• You can adjust the output level from “–6 dB” to “+6 dB.”

5Repeat steps 3 and 4 to adjust the other speaker output level.

6Press Cursor (5 / ∞ / 3 / 2) to select “TEST TONE,” then press ENTER.

Test tone stops.

7When finished, press Cursor (5 / ∞ / 3 / 2) to move

to “EXIT,” then press ENTER.

EXPERT SPEAKER SETTING menu disappears.

7Selecting the speaker for bass output

You can select the speaker for bass output according to your preference.

1Display EXPERT SPEAKER SETTING menu.

•See page 38.

2Press Cursor (5 / ∞ / 3 / 2) to move to “BASS,” then press ENTER.

3Press Cursor 3 or 2 to select your desired setting.

•L/R : to output the bass signals through the FRONT SUBWOOFERS terminals.

•S.woofer : to output the bass signals through the subwoofer connected to the SUB-WOOFER 5.1ch OUT jack.

4When finished, press Cursor (5 / ∞ / 3 / 2) to move to “EXIT,” then press ENTER.

EXPERT SPEAKER SETTING menu disappears.

7Adjusting the subwoofer output levels

You can adjust the output level according to your preference.

1Display EXPERT SPEAKER SETTING menu.

• See page 38.

2 Press Cursor (5 / ∞ / 3 / 2) to move to “SUB

WOOFER,” then press ENTER.

• You can adjust the output level from “–6 dB” to “+6 dB.”

3Press Cursor 3 or 2 to adjust the output level, then

ENTER.

4When finished, press Cursor (5 / ∞ / 3 / 2) to move

to “EXIT,” then press ENTER.

EXPERT SPEAKER SETTING menu disappears.

Changing the Display Settings

On DISPLAY menu, you can change the following display settings.

MONITOR TYPE		4:3 LB
SCREEN SAVER		MODE 2
ON SCREEN GUIDE		ON
		EXIT
PRESS	KEY

•MONITOR TYPE :

Set the monitor type to use while playing back a DVD recorded with 16:9 wide screen video signal.

Selectable types—4:3 LB , 16:9 WIDE, 4:3 PS . (See page 42.)

•SCREEN SAVER :

Select the screen saver to prevent a TV monitor from burning out.

–Select “MODE 1” to activate the screen saver by making the TV screen dark.

–Select “MODE 2” to activate the screen saver by showing the original screen-saver.

–Select “OFF” to deactivate this function.

When “MODE 1” or “MODE 2” is selected, screen saver functions if still (static) picture is shown for more than 5 minutes.

•ON SCREEN GUIDE :

By watching the on-screen indications shown on the TV screen, you can confirm what you are doing while operating the DVD player.

–Select “ON” to show the on-screen indications.

–Select “OFF” to deactivate this function.

– 41 –