Weider WEBE19300 manual Locknuts 11. Do not tighten the Nylon Locknuts Yet

Page 9

10. Press a 60mm Square Inner Cap (55) into each end

10

38

 

of the Top Crossbar (9). Attach the Top Crossbar to

 

55

 

the Uprights (1) using four Joint Plates (12), eight

 

6

 

M10 x 80mm Bolts (41), and eight M10 Nylon

 

 

 

 

 

Locknuts (11). Do not tighten the Nylon Locknuts

 

9

38

yet.

 

 

 

 

 

 

Secure the Top Crossbar (9) to the Weight Guides

 

 

6

 

 

 

(18) using two M10 x 30mm Bolts (38) and two M10

 

11

55

Small Washers (6).

 

 

 

 

 

 

12

11

 

 

 

 

 

 

12

 

41

 

 

 

18

41

 

 

 

1

1

 

 

 

 

 

 

18

11. Press Carriage Bushings (27) into the ends of the

11

 

 

Weight Carriage (22). Press 50mm Round Inner

2

 

 

 

Caps (25) into the ends of the weight tube on the

 

Angled End

25

Weight Carriage.

 

 

 

27

 

 

 

 

Insert an M10 x 20mm Bolt (26) into the bracket on

 

the Weight Carriage (22).

Weight Tube

 

Slide the Weight Carriage (22) onto the Rear

 

 

27

 

22

 

Upright (2) as shown. Make sure that the Weight

 

 

 

 

 

Carriage and the Rear Upright are oriented as

25

 

 

shown.

26

 

12. Refer to the inset drawing. Press a Carriage

12

 

27

Bushing (27) into the top of the Carriage Stop (28)

 

 

 

 

 

as shown.

54

 

28

 

 

Slide the Carriage Stop (28) onto the lower end of

11

 

 

the Rear Upright (2). Attach the Carriage Stop to

28

 

 

 

the Rear Upright with an M8 x 70mm Bolt (30) and

6

 

30

an M10 Nylon Locknut (54).

2

 

 

 

 

 

 

Slide the Rear Upright (2) onto the bracket on the

 

6

30

 

 

Rear Base (3). Attach the Rear Upright to the Rear

 

 

Bracket

Base using two M10 x 65mm Bolts (56), four M10

 

3

 

 

Small Washers (6), and two M10 Nylon Locknuts

 

 

 

(11). Do not tighten the Nylon Locknuts yet.

 

 

 

9

Image 9
Contents Model No. WEBE19300 Serial No Customer HOT LineMon.ÐFri., 6 a.m.Ð6 p.m. MST Table of Contents ¥ Misuse of this product may result in serious injury Important PrecautionsBefore You Begin Right SideLeft Side Part Identification ChartÑModel No. WEBE19300 R0800B Assembly Some small parts may be pre-assembledLocknuts yet Page Make sure the Safety Spotters are oriented exactly as shown Weight Gliders are oriented exactly as shownTighten the M8 x 16mm Screws 50 used in steps 6 Do not tighten the Nylon Locknuts yet Locknuts 11. Do not tighten the Nylon Locknuts YetLocknut. The Pulley must be able to turn freely Tighten all Nylon Locknuts used in steps 1 throughNylon Locknut the Pulley must be able to turn freely Adjusting the Weight Rack Using the Weight AdapterUsing the Locking BAR Attaching Weights to the Barbell or the Weight Carriage Using the Safety SpottersTightening the Cables Pulley must be able to turn freelyExercise Guidelines Muscle Chart Cooling DownStaying Motivated Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part ListÑModel No. WEBE19300Exploded DrawingÑModel No. WEBE19300