Weider WEBE11880 manual Go back and tighten all Locknuts and Jamnuts, Hole

Page 7

5.Press a 1 1/2Ó x 1 1/2Ó Inner Cap (7) into the end of the Bench Frame (5). Place the bracket on the Bench Frame over the 5/16Ó x 2Ó Carriage Bolts (22) in the Stabilizer. Hand tighten two 5/16Ó Nylon Locknuts (15) onto the Bolts. Do not tighten the Nylon Locknuts yet.

See drawing 5A. Have one person hold up the end of the Bench Frame (5) while the second person slides the Bench Rod (8) through the indicated hole in the Lat Upright (34) until the end of the Rod barely sticks through the Upright.

Line up a Bench Spacer (4) with the Bench Rod (8) and slide the Rod through the Spacer. Slide the Bench Rod through the pre-assembled Bench Frame Bushings (6) on the Bench Frame. Slide the Bench Rod through the second Bench Spacer (4) and then into the Upright (49).

Secure the end of the Bench Rod (8) going into the Upright (49) with a 1Ó Washer (51), a 5/16Ó Washer (53) and a Bench Rod Bolt (41).

Secure the end of the Bench Rod (8) going through the Lat Upright (34) with a 1Ó Washer (51), a 5/16Ó Washer (53) and a Bench Rod Bolt (41).

Go back and tighten all Locknuts and Jamnuts

6.Attach a Backrest Bracket (2) to the Backrest (1) with two 1/4Ó x 1/2Ó Screws (3). Make sure the

Backrest Bracket is oriented as shown (note the position of the indicated hole). Do not tighten the Screws yet.

6a. Refer to drawing 6a. Hold the Backrest (1) in a vertical position as shown and slide the end of the attached Backrest Bracket (2) onto the welded rod on the Bench Frame (5). Hold the other Backrest Bracket (2) at an angle as shown and slide it onto the rod.

Refer to drawing 6b. Attach the Backrest Bracket

(2)to the Backrest (1) with two 1/4Ó x 1/2Ó Screws

(3).Note: The Screw nearest the rod should be attached first.

Fully tighten all four 1/4Ó x 1/2Ó Screws (3) used in steps 6 and 6a.

5

 

 

7

 

 

5

 

 

15

15

 

 

 

 

21

 

 

50

 

22

 

 

5A

 

49

 

41

51

4

 

 

 

34

 

 

 

53

 

 

6

 

 

 

 

 

4

8

 

 

51

 

 

 

5

 

 

41

 

 

 

 

 

 

53

6

 

 

3

 

 

 

 

 

2

 

 

3

 

1

 

 

 

Hole

6a

 

6b

 

 

1

 

2

2

 

 

 

 

1

 

 

3

 

 

Rod

 

 

5

7

Image 7
Contents Mon.ÐFri., 6 a.m.Ð6 p.m. MST Model No. WEBE11880 Serial NoSerial Number Decal Customer HOT LineTable of Contents Keep hands and feet away from moving parts Important PrecautionsSide Leg Lever Foam Pads Weight TubeBefore You Begin RightLocknuts yet Assembly¥ Assembly requires two people Make Things Easier for YourselfStabilizer must be facing the floor Do not tighten the Jamnuts yetStabilizer Holes Hole Go back and tighten all Locknuts and JamnutsBracket Lubricate Front View LocknutPress a 3/4Ó Inner Cap 12 into each end of the Support Rod Adjusting the Weight BenchAdjusting the Backrest Using the LAT BARExercise Guidelines Staying Motivated Muscle ChartExercise Form Cooling DownPart Identification Chart Model No. WEBE11880 R0699A Bumper Screw UserÕs Manual Square Nut Exercise Poster Part List Model No. WEBE11880Qty Description 16Ó Nylon Locknut Upright Endcap 1Ó Inner CapExploded Drawing Model No. WEBE11880 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT