Weider WEBE03320 Tighten the M10 Nylon Locknuts 19 used in steps, Bracket is oriented as shown

Page 7

3.Press two 50mm Round Outer Caps (12) onto the ends of the other Stabilizer (4).

Attach the Stabilizer (4) to the Rear Leg (3) with two M10 x 60mm Carriage Bolts (18) and two M10 Nylon Locknuts (19). Be sure the indents and the decal on the Stabilizer are oriented as shown. Do not tighten the Locknuts yet.

Attach the Rear Leg (3) to the Frame (1) with two M10 x 25mm Bolts (25) and two M10 Washers (20).

Tighten the M10 Nylon Locknuts (19) used in steps 1–3.

4.Press the 25mm x 50mm Inner Cap (15) into the end of the Backrest Frame (5).

Attach the Pivot Bracket (6) to the Backrest Frame (5) with two M8 x 65mm Bolts (26) and two M8 Nylon Locknuts (27). Be sure the Pivot

Bracket is oriented as shown.

Attach the Backrest (7) to the Backrest Frame (5) with four M6 x 16mm Bolts (24). Be sure the

Backrest is oriented as shown.

5.Slide the Pivot Bracket (6) through the slot in the Frame (1).

Lubricate the M10 x 85mm Bolt (23). Attach the Backrest Frame (5) to the Frame (1) with the Bolt and an M10 Nylon Locknut (19). Do not over- tighten the Locknut; the Backrest Frame must be able to pivot easily.

Insert the Locking Pin (21) into the Frame (1) and through an adjustment hole in the Pivot Bracket

(6).

6.Attach the tether on the Locking Pin (21) to the bottom of the Frame (1) with the M4 x 16mm Screw (28).

Attach the Seat (8) to the Frame (1) with four M6 x 45mm Bolts (16) and four M6 Washers (22). Be sure the wide end of the Seat is on the side shown.

3

 

 

 

Warning

 

 

 

 

12

Decal

 

 

 

 

 

 

Indents

1

3

19

 

 

 

18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

20

 

20

19

 

4

 

 

 

 

 

25

 

 

 

 

4

 

 

 

 

 

 

 

7

 

 

 

 

15

 

 

 

 

 

 

 

24

 

 

5

24

 

 

 

 

 

 

27

 

 

 

 

 

 

 

6

 

26

 

 

 

 

 

 

 

5

 

 

 

 

 

 

19

5

 

 

 

 

 

6

 

 

 

1

21

 

 

Slot

 

 

 

 

 

 

 

23

 

 

Adjustment

 

 

 

 

Lubricate

 

 

Holes

 

 

 

 

 

6

 

 

 

 

 

8

 

 

 

 

 

 

Wide

 

 

 

 

 

End

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

21

 

 

 

 

22

28

 

 

 

 

 

 

 

 

16

 

16

 

 

7

Image 7
Contents Model No. WEBE03320 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Before YOU Begin Part Identification Chart Make Things Easier for Yourself AssemblyBracket is oriented as shown Tighten the M10 Nylon Locknuts 19 used in stepsBackrest is oriented as shown Adjusting the Backrest AdjustmentsExercise Guidelines Cooling Down Muscle ChartStaying Motivated Key No. Qty Description Part LIST/EXPLODED DRAWING-Model No. WEBE03320Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT