Weider WEBE09913 user manual Before You Begin, Assembly-Ab-Tilt & Tone

Before You Begin

Thank you for selecting the versatile WEIDER® TWO TONE body toning system. The TWO TONE body toning system is designed to help you develop every major mus- cle group of the body. Whether your goal is a shapely fig- ure, dramatic increase in muscle size and strength, or a healthier cardiovascular system, the TWO TONE body ton- ing system will help you achieve the specific results you want.

For your benefit, read this manual carefully before using the WEIDER® TWO TONE body toning system. If you have additional questions, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (exclud- ing holidays). To help us assist you, please mention the product model number (WEBE09913) and the serial num- ber found on a decal attached to the body toning system (see the front cover of this manual).

Assembly—Ab–Tilt & Tone

1.Press two 2” Round	1
Outer Caps (23) onto	34	12
each of the two Front		34
Stabilizers (9) and
	23
the two Rear
	9	23
Stabilizers (not
	31
shown). Note: The
Front Stabilizers are

shorter than the Rear Stabilizers.

Attach a Front Stabilizer (9) to the Ab Leg (12) with two 5/16” x 2 1/2” Carriage Bolts (31) and two 5/16” Nylon Locknuts (34). Attach a Rear Stabilizer (not shown) to the other end of the Ab Leg in the same manner.

2.Insert a 5/16” x 3”	2	13
Carriage Bolt (32)
into the center hole in
the Large Support		15
Plate (14). Attach the
Large Support Plate		40

3.Hold the Metal	3
Bushing (27) inside
	11
the Seat Frame (15).
		30
Slide a 5/16” x 1 3/4”
		27
Bolt (33) into the
upper hole in the Ab	33	34
Frame (11), the Seat
Frame, and the Metal		35
Bushing.
		15
Slide another 5/16” x
1 3/4” Bolt (33) into
the lower hole in the
Ab Frame (11) and the Seat Frame (15).

Secure the two 5/16” x 1 3/4” Bolts (33) with two 5/16” Washers (35) and two 5/16” Nylon Locknuts (34).

Press a 1” x 2” Inner Cap (30) into the upper end of the Seat Frame (15).

to the Large Seat	14	32
(13) with two 1/4” x
	32
3/4” Screws (40).		40
	30
Insert a 5/16” x 3”	38	12
Carriage Bolt (32)	40
into the indicated		46 35
hole in the Seat
Frame (15). Insert

the 5/16” x 3” Carriage Bolt in the Large Support Plate (14) through the rear hole in the Seat Frame.

Hold a 1/4” Washer (38) and a 1/4” x 3/4” Screw (40) inside the Seat Frame (15), and use them to attach the

4.Remove the 1/4” x 1/2” Type 23 Screws

(47)from the Ab Frame (11). Attach the Ab Handlebars

(10)to the Ab Frame with the two 1/4” x 1/2” Type 23 Screws.

Press a 1 1/8” Round Inner Cap (16) into each Ab Handlebar (10).

4	16	11	48	39
10		47	16
				47
17			10

Large Seat (13) to the Seat Frame. Press a 1” x 2” Inner Cap (30) into the lower end of the Seat Frame.

Secure the two 5/16” x 3” Carriage Bolts (32) to the Ab Leg (12) with two 5/16” Washers (35) and two 5/16” Nylon Jamnuts (46).

Wet the Ab Handlebars (10) and the Ab Frame (11) with soapy water. Slide a Cover Sleeve (17) onto each Ab Handlebar.

Insert the Tie Wrap (39) through the hole in the Spring Cover (48), and secure it around the Seat Frame (15). Cut the excess Tie Wrap.