Assembly—Rock & Tone
5. | Attach a Rear |
| Stabilizer (8) to the |
| Base (2) with two |
| 5/16” x 2 1/2” |
| Carriage Bolts (31) |
| and two 5/16” Nylon |
| Locknuts (34). |
6. | Attach a Front |
| Stabilizer (9) to the |
| Adjustment Frame |
| (3) with two 5/16” x |
| 2 1/2” Carriage |
| Bolts (31) and two |
| 5/16” Nylon |
5 |
|
|
|
| 31 | 8 |
|
|
|
| 34 |
|
| 34 | 2 |
|
|
| |
6 | 2 | 41 | 6 |
| 3 |
| |
|
|
| |
|
|
| 35 |
26 | 49 |
|
|
|
| 34 | 34 |
8. | Slide a Grip (22) | 8 |
|
| onto each end of the |
| |
| 29 |
| |
| Handlebar (21). |
| |
| 1 | 21 22 | |
|
| ||
| Attach the |
| |
|
|
| |
| Handlebar (21) to | 35 |
|
| the Backrest Frame | 42 | |
|
| ||
| (1) with two 5/16” x |
| 38 |
| 2” Bolts (42), two |
| 50 |
| 5/16” Washers (35), | 22 | |
| and two 5/16” Nylon | 34 |
|
| Locknuts (34). | 35 |
|
|
|
|
Attach the Small
Seat (29) to the Handlebar (21) with two 1/4” x 1 1/2” Screws (50) and two 1/4” Washers (38).
Locknuts (34). |
9 |
| 31 |
9. Insert a 1/4” x 2” |
Carriage Bolt (45) |
9 | 38 |
Slide the Adjustment
Frame (3) through the Slider Bushing (49) and into the Base (2). Insert the Adjustment Pin (26) into the indi- cated hole in the Base and a hole in the Adjustment Frame.
Attach the Press Plate (6) to the Adjustment Frame (3) with two 5/16” x 1 3/4” Carriage Bolts (41), two 5/16” Washers (35), and two 5/16” Nylon Locknuts (34).
into the center hole |
of the Support Plate |
(20). |
Attach the Support |
Plate (20) to the |
Backrest (4) with |
two 1/4” x 3/4” |
Screws (40). |
43 | 1 |
| 4 |
|
|
| |
38 |
| 40 | 20 |
|
|
| |
44 |
|
|
|
|
|
| 45 |
7. Make sure the End | 7 |
|
Plate (19) is inside |
| |
24 |
| |
the Angled Cap |
| |
1 |
| |
(18). Press the |
|
|
Angled Cap onto the |
|
|
bottom end of the |
|
|
Backrest Frame (1). | 34 | 35 |
Press a 1 1/2” |
| |
|
| |
Square Inner Cap | 7 | 42 |
(24) into the top of |
| |
|
| |
the Backrest Frame. | 34 | 35 |
Attach the Pivot | 36 | 19 |
| ||
Frame (7) to the | 2 |
|
Backrest Frame (1) |
| 18 |
with two 5/16” x 2” | 37 |
|
Bolts (42), two 5/16” |
| |
|
| |
Washers (35), and |
|
|
two 5/16” Nylon Locknuts (34). |
| |
Attach the Pivot Frame (7) to the Base (2) with a 3/8” x 2 3/4” Bolt (37) and a 3/8” Nylon Locknut (36). Do not over tighten the Locknut; the Pivot Frame must be able to pivot easily.
Attach the Backrest (4) to the the Backrest Frame (1) with the 1/4” x 2” Carriage Bolt (45), a 1/4” Washer (38), and a 1/4” Nylon Locknut (44).
Secure the Backrest (4) with a 1/4” x 2” Screw (43) and a 1/4” Washer (38).
The use of the remaining parts will be explained in Adjusting The Body Toning System.