Electrolux Full Size Tumble Action Washer important safety instructions Installation, Cable, Tie

	INSTALLATION	Models equipped with gravity drain: Run the machine's drain
1. Run some water from the hot and cold		hose into an oversized floor drain or drain trough. The entire
	faucets to flush the water lines and remove	length of the drain hose must be below the drain outlet on the
	particles that might clog up the water valve	machine.
	screens.
2. Remove the inlet hoses and rubber washers
	from the plastic bag and install the rubber
	washers in each end of the inlet hoses.
3.	(90° elbow end) Carefully connect the inlet hose marked "HOT"
	to the outside "H" outlet of the water valve. Tighten by hand,
	then tighten another 2/3 turn with pliers. Carefully connect the
	other inlet hose to the inside "C" outlet of the water valve. Tighten
	by hand, then tighten another 2/3 turn with pliers. Do not
	crossthread or over-tighten these connections.
4.	Connect the inlet hose ends to the HOT and
	COLD water faucets tightly by hand, then tighten
	another 2/3 turn with pliers. Turn the water on
	and check for leaks.	NOTE: The drain pipe or floor drain, into which the drain hose is
5. On machines equipped with drain pump, form a		placed, MUST be at least 1/2 inch larger in diameter
	U shape on the end of the drain hose, with the	than the drain hose. This will insure that the sewer line
	hose pointed toward the drain.	cannot back up into the washing machine.
	NOTE: If the drain hose is placed in a standpipe	8. Plug the power cord into a grounded outlet.
	without forming a U shape, a siphoning action	NOTE: Check to ensure the power is off at the circuit breaker/
	could occur. There must be an air gap around the
	drain hose. A snug hose fit can also cause a	fuse box before plugging the power cord into an outlet.
	siphoning action.	9. Turn on the power at the circuit breaker/fuse box.

6.On machines equipped with gravity

drain, connect one end of the drain	10. Be sure you have read the "Important Safety Instructions" on
hose to the drain outlet of the	pages 2-3 before operating this washer.
machine, using the provided clamp.	11. Run the washer through a complete cycle. Check
	for water leaks and proper operation.
7. Carefully move the washer	12. Keep these instructions for future reference.
to its final location.

NOTE: A wiring diagram is located inside the washer on the

NOTE: Do not use the service panel. dispenser drawer or door

to lift washer.

8. With the washer in its final		REPLACEMENT PARTS
position, place a level on top		If replacements parts are needed for your washer, contact the
of the washer. Adjust the front
		source where you purchased your washer, call 1-800-944-9044, or
leveling legs up or down to
		visit our website, www.frigidaire.com, for the Frigidaire Company
ensure the washer is resting
		Authorized Parts Distributor nearest you.
solid. Turn the lock nuts on
each leg up towards the base		Destroy the carton and plastic bags after the
of the washer and snug
		washer is unpacked. Children might use them for play. Cartons
with a wrench.
		covered with rugs, bedspreads, or plastic sheets can become airtight
NOTE: Keep the leg		chambers causing suffocation. Place all materials in a garbage
		container or make materials inaccessible to children.
extension at a minimum to
prevent excessive vibration.	Cable	The instructions in this manual and all other
The farther out the legs are
	Tie	literature included with this washer are not meant to cover every
extended the more the
		possible condition and situation that may occur. Good safe practice
washer will vibrate.
		and caution MUST be applied when installing,operating and
Rear leg adjustments are also		maintaining any appliance.
accessible through the front
service panel.
9. Models equipped with drain		Maximum benefits and enjoyment are achieved when all the Safety
		and Operating instructions are understood and practiced as a
pump: Place the formed end of	Cable
		routine with your laundering tasks.
the drain hose in a laundry tub	Tie
or a standpipe and secure with
the cable tie provided in the
enclosure package.

5