Wash and Rinse Surface, Add Engine Oil

,_ Warning:the cleaningBesystemextremelyfromcarefulladder,if youscaffoldingmust use or any other relatively unstable location. When you press the trigger, the recoil from the initial spray could force you to fall, or if you are too close to the cleaning surface, high pressure could force you off a climbing apparatus.

•Start at lower portion of area to be washed and work upward, using long, even overlapping strokes.

•Allow detergent to 'soakin'(between 3-5 minutes) before washing and rinsing. Reapply as needed to prevent surface from drying.

Wash and Rinse Surface

This Craftsman Cleaning System permits regulatLonof output water pressure by varying the engine speed. The Pressure Command TM found on the front panel may be set, as follows:

Pressure	Low	to	_	High
Duty	Light	Medium		Heavy
Application	Auto	Concrete		Paint removal
	Boat	Driveway		Degreasing
	Furniture	Deck

After you have applied detergent, scour the surface with the high pressure water stream and then dnse it clean, as follows:

•Pull adjustable nozzle backward until it snaps to get high pressure mode. Chemical will not flow when in the high pressure mode.

•Adjust Pressure Command TM control to obtain desired water pressure.

•Expand the spray pattern for a more gentle rinsing action. Start at top of area to be dnsed, working down with same action as for cleaning.

,_ CAUTION: Test a small area of the surface to be cleaned. Make sure there is no damage

caused by the high pressure spray.

RINSE SYSTEM AFTER EVERY'USE

it is imperative that the chemical selector system be rinsed after each use to prevent clogging or leaks:

•Fill the System Rinse reservoir with clean water.

•Before disconnecting the water supply, siart your cleaning system.

ACAUTION:System, makeBeforesurestartingyou haveyourreadCleaningand followed the instructions in the sections =Before Starting the Cleaning System" on page 7 and =To Start the Cleaning System" on page 8.

•Push adjustable nozzle forward to get.low pressure mode.

Rotate the Dial-A-Cleaner TM selector knob to the

•letter corresponding to the System Rinse tank. As clean rinse water is drawn through the system, continue the flow until no detergent foam is observed.

•Rotate the Dial-A-Cleaner TM selector knob to the

OFF position.

BEFORE STARTING THE CLEANING SYSTEM

To operatette engine you willneed to do the following:

Add Engine Oil

Only use high quality detergent oil rated with API service classification SF or SG. Select the oil'sSAE

viscosity grade according to your expected operating temperature:

colder -<-----32°F ._ warmer

	I
5W30	SAE 30

Although multi-viscosityoils (5W30, 10W30, etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more

frequently to avoid possible damage from running low on oil.

Place pressure washer system on a level surface

Clean area around oil fill and remove oil dipstick.

Pour oil from enclosed bottle into the oil fill opening until oil reaches the full mark on the oil dipstick.

Stop and check the oil level periodically. Do not overfill.

•Install oil dipstick, hand tighten securely.

Add Gasoline

•Use regular unleaded gasoline with the cleaning system engine. Fuel tank capacity is 3 U.S, quarts.

,_ fuelDANGER:tank whenNeverenginefill fuelis runningtank indoorshot. Never. Do notfill smoke when filling fuel tank.

AleaveAUTION:room Dofor expansionnot overfill. the fuel tank. Always

,_ CAUTION:blended fuelsExperience(called gasoholindicatesor usingthat alcoholethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.