JVC RX-888RBK manual Frequency appears on the display, Crossover Frequency Setting

Page 18

English

Crossover Frequency Setting

Small speaker cannot reproduce the bass sound very well. So, if you have used a small speaker any for the front, center, or rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).

To use this function properly, you need to set this crossover frequency level according to the size of the small speaker connected.

•This function takes effect only when playing back a source using Dolby Pro Logic, Dolby Digital, DTS Digital Surround, or MPEG Multichannel. However, if you have selected “LARGE” for all speakers (see page 14), this function will not take effect.

On the front panel ONLY:

SETTING

1.Press SETTING repeatedly until “CROSSOVER FRQ” (Crossover

Frequency) appears on the display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to select the crossover frequency level according to the size of the small speaker connected.

• As you turn it, the display changes to show the following:

80Hz100Hz120Hz

• Use the following comments as reference when adjusting.

80Hz: Select this when the cone speaker unit built in the speaker is about 12 cm (4 3/4 inches).

100Hz: Select this when the cone speaker unit built in the

speaker is about 10 cm (3 15/16 inches).

120Hz: Select this when the cone speaker unit built in the speaker is about 8 cm (3 3/16 inches).

Note:

Crossover frequency setting is not valid for the DVD MULTI playback

mode.

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using Dolby Digital, DTS Digital Surround, or MPEG Multichannel, follow the procedure below.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

 

“LFE ATT” (Low Frequency

 

Effect Attenuator) appears on the display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to select the low frequency effect attenuator level.

• As you turn it, the display changes to show the following:

0dB 10dB

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Note:

Low frequency effect attenuator setting is not valid for the DVD MULTI playback mode.

Dynamic Range Compression Setting

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.

•This function takes effect only when playing back a source using Dolby Digital.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

 

“D. RANGE COMP.” (Dynamic

 

Range Compression) appears on

 

the display.

 

The display changes to show the current setting.

 

 

MULTI JOG

2.Turn MULTI JOG to select the appropriate item about the compression level.

• As you turn it, the display changes to show the following:

OFF MID MAX

OFF: Select this when you want to enjoy surround with its full dynamic range. (No effect applied)

MID: Select this when you want to reduce the dynamic range a little. (Factory setting)

MAX: Select this when you want to apply the compression effect fully. (Useful at night)

Note:

Dynamic Range Compression setting is not valid for the DTS Digital Surround, MPEG Multichannel, and DVD MULTI playback mode.

15

Page 17 Page 19
Image 18
Page 17 Page 19
Contents RX-888RBK Per I’ltalia Español Italiano Table of Contents Remote Control Parts IdentificationFront Panel Connecting the FM and AM MW/LW Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM MW/LW Antenna ConnectionsConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers About the speaker impedanceVideo component connections VHS VCR‚ To composite video output To S-video outputTo composite DVD playerPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Digital connectionsBasic Operations Turning the Power On and Off StandbyFrom the remote control Selecting the Source to PlayEtc Adjusting the VolumeSelecting the Front Speakers Turn Source Selector toAdjusting the Subwoofer Output Level Attenuating the Input SignalListening at Low Volume Loudness Muting the SoundSetting the Subwoofer Information Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeShowing the Text Information on Display Front, Center, and Rear Speaker Setting Setting the Speakers for the DSP ModesCenter Delay Time Setting Rear Delay Time SettingDynamic Range Compression Setting Crossover Frequency SettingLow Frequency Effect Attenuator Setting Frequency appears on the displayUsing the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed above Press ONE Touch OPERATION. OnetouchoperationUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Assigning Names to Preset Stations Selecting the FM Reception ModeTo search for a program using the PTY codes Using the RDS Radio Data System to Receive FM StationsWhat information can RDS signals provide? Searching for a Program by PTY CodesTurn Multi JOG until the PTY Press PTY Search whilePTY codes Program type appears on Display Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Press TA/NEWS/INFO untilUsing the SEA Modes Selecting Your Favorite SEA ModeCreating Your Own SEA Mode DAP modes Using the DSP Modes3D-PHONIC modes With 3D Theater selectedDVD Multi Playback Mode Surround modesAvailable DSP Modes According to the Speaker Arrangement FrontAdjusting the 3D-PHONIC Modes Adjusting the DAP ModesAdjusting the Surround Modes Press DOLBY/DTS/MPEG An appropriate Surround modeAdjust the center tone Surround ON/OFF to activateDIG Theater appears on Display JVC Theater Surround adjustmentsRepeatedly until Theater or Center tone level you wantSelect and play a sound source Activating the DSP ModesLamp on the button lights up Press Surround ON/OFF soPress Surround Mode repeatedly until Mode you want appears on DisplayTo cancel the DSP mode For the other DSP modesDVD Multi appears on Display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Tone appears on the display10 keys are activated for adjusting the sound Press DVD Multi so that DVDMulti appears on the display Using the On-Screen Menus Press %/ Þto move Input Attenuator modePress %/ Þto move to Sound CONTROL, then press @/ # To Subwfr LevelPress %/ Þto move to SEA, then press @ / # To SEA ModePress %/ Þto move To SEA, then press @ Press %/ Þto move to Surround LEVEL, then press @ / #Press %/ Þto move to SETTING, then Press @/ # Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Setting the Basic Setting Items Also seePress %/ Þto move to Tuner CONTROL, then press @/ # To Preset NameTo Preset Then press SETSame time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionDisc Search Only for CD Player Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Title InputTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Disc Information screen appears on the TVPress %/ Þto move to SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress %/ Þto move To SEARCH, then Press %/ Þto move to Performer Then press SETPress %/ Þto move To Title Input Then press SET Press %/ Þto move To Search Then press SETPress %/ Þto move To GENRE, then Press SET Entering the Disc InformationTo insert a space, press %/ Þ Press Text Display while MD is selected as the sourcePress %/ Þto move to the genre you want, then press SET To correct an incorrect characterCD player Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerMD recorder TurntableCassette deck DVD playerRelease TV/CATV/DBS If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TV/CATV DBSIf there are more than one code listed for your brand Release VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for TV RBM MTCNEI RFTManufacturers’ codes for DBS tuner ESC Manufacturers’ codes for Catv convertersManufacturers’ codes for VCR ITV004 Samsung 240 Sansui 041, 067 Sanyo 046 Saville 352Schaub Lorenz 000, 005, 041, 104 Schneider 000, 072 White WestinghouseTroubleshooting Problem Possible Cause SolutionAudio SpecificationsAmplifier VideoAM MW/LW tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF GeneralEN, GE, FR, NL, SP, IT 0499HIMMDWJEM

RX-888RBK specifications

The JVC RX-888RBK is a powerful and versatile stereo receiver designed for audiophiles and casual listeners alike. Packed with a range of features, this receiver provides exceptional sound quality, making it suitable for various applications, from home theaters to music listening.

At the heart of the RX-888RBK is a robust amplification system, delivering 100 watts of power per channel. This ensures that even large rooms can be filled with clear and dynamic sound, achieving a rich audio experience whether you're watching movies or enjoying your favorite music. The receiver supports FM and AM radio, allowing users to tune into their favorite stations with ease.

One of the standout features of the RX-888RBK is its multi-input capability. It comes equipped with multiple audio inputs, including six line-level inputs, a dedicated phono input for turntables, and two tape inputs/outputs. This flexibility ensures that users can connect various devices, such as CD players, tape decks, and gaming consoles, without losing audio quality.

The RX-888RBK also boasts a built-in graphic equalizer that allows for precise audio tuning. This feature provides users the ability to adjust the sound profile to suit their preferences, enhancing bass, treble, and midrange frequencies. This level of customization ensures optimal sound reproduction across a variety of music genres.

Another significant characteristic of the RX-888RBK is its user-friendly design. The front panel layout is intuitive, featuring clearly labeled controls and a large display. This makes it easy for users to navigate through settings and controls. Additionally, the remote control that accompanies the receiver provides added convenience, allowing users to adjust settings from the comfort of their couch.

The receiver's solid build quality enhances durability, while the sleek design fits well in any home entertainment setup. Furthermore, the RX-888RBK includes advanced protection circuitry, which helps to prevent damage to both the receiver and connected speakers during operation.

In terms of connectivity, the RX-888RBK offers standard speaker outputs for easy connection to a variety of speaker systems, ensuring compatibility with both stereo and surround sound applications.

In summary, the JVC RX-888RBK is an excellent choice for those seeking a reliable and feature-packed stereo receiver. With its powerful audio output, multiple connectivity options, customizable sound settings, and user-friendly interface, this receiver delivers a comprehensive audio experience that meets the demands of both casual listeners and dedicated audiophiles. Whether for music playback or home theater use, the RX-888RBK provides a solid foundation for any audio setup.
Top Page Image Contents