Hamilton Beach 14X60 Optional Features on select models, Caring and Cleaning, Vertical Steam

Page 4

840120200 Ev01.qxd 10/10/03 12:32 PM Page 6

Optional Features (on select models)

Vertical Steam

1. Follow Steps 1 through 6 in “To Steam Iron.”

2. Hang garment in a location that is not susceptible to damage from heat or moisture. Do not hang in front of wallpaper, window, or mirror.

3.Hold iron about 6 inches away from garment and press and release the Blast Button to steam out wrinkles. Do not press Blast Button more than once every 2 seconds.

4.To turn iron off, turn Temperature Control Dial to OFF (O). Unplug iron.

5.Empty water from the iron following directions in “Caring for Your Iron.”

NOTE: Do not allow hot soleplate to touch delicate garments.

Auto Shutoff Reset Button/Light

This light comes on when the iron is first plugged in. After one hour, the iron will shut off and the light will go out. Push the Reset Button/Light to turn the iron back on.

Power On Light

On units not provided with Auto Shutoff, this light comes on when the iron is plugged in and remains on until the iron is unplugged. The light stays on even if Temperature Control Dial is turned to OFF (O).

6

Caring and Cleaning

Iron Storage

1.The water tank of your iron should be emptied after each use. Turn Temperature Control Dial to OFF (O). Unplug the iron and hold over a sink. Slowly tilt pointed end of iron down over sink. Water will run out of water tank opening.

2.After iron is complete cool, wrap cord loosely around iron and store in upright position. Do not store iron laying flat on soleplate.

Soleplate

1.Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate.

2.To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads.

3.Always store iron upright in the heel rest position.

Self-Clean

To keep the steam vents clear of any build-up, follow these instructions each time you iron using steam.

1.Turn Temperature Control Dial to OFF (O) and set Adjustable Steam Knob to DRY. Fill iron with water to 12 of its maximum capacity.

2.Turn Temperature Control Dial to Linen setting and let iron heat for 2 minutes. Keep Adjustable Steam Knob on DRY.

3.Turn Temperature Control Dial to OFF (O). Unplug iron and hold over a sink with soleplate facing down.

4.Turn Adjustable Steam Knob to MAX, while pressing Blast of Steam button often. Boiling water and steam will flow out of steam vents. Allow all water to drain from iron.

5.Gently move iron front to back to allow water to clean entire soleplate area.

6.If water still remains inside of soleplate, reheat iron as indicat- ed in Step 2. Boiling water and steam could still flow out of

steam vents.

7

Image 4
Contents USA En MéxicoImportant Safety Instructions Parts and FeaturesRead ALL Instructions Before Using This appliance is intended for household use onlyFeatures Before First UseTo Dry Iron To Steam IronOptional Features on select models Caring and CleaningAuto Shutoff Reset Button/Light Power On LightTroubleshooting Fabric Setting ChartCustomer Service Limited WarrantySalvaguardias Importantes LEA Todas LAS Instrucciones Antes DE UsarlaGuarde Estas Instrucciones Piezas y característicasAntes del primer uso Instrucciones EspecialesCómo planchar en seco Cómo planchar al vaporCaracterísticas Botones de rocío y golpe de vaporCaracterísticas opcionales en modelos selectos Cuidado y limpiezaProblema Elementos que SE Deben Chequear Solución de problemasAutolimpieza Tabla de graduaciones de las telas Elementos que SE Deben ChequearDistrito Federal JaliscoChihuahua Nuevo LeonHamilton Beach PROCTOR-SILEX, INC